Sony VCT-670RM - Manual (Page 2)

English Français
WARNING
This equipment has been tested
and found to comply with the
limits for a Class B digital device,
pursuant to Part 15 of the FCC
Rules. These limits are designed
to provide reasonable protection
against harmful interference in a
residential installation. This
equipment generates, uses, and
can radiate radio frequency
energy and, if not installed and
used in accordance with the
instructions, may cause harmful
interference to radio
communications. However, there
is no guarantee that interference
will not occur in a particular
installation. If this equipment
does cause harmful interference
to radio or television reception,
which can be determined by
turning the equipment off and
on, the user is encouraged to try
to correct the interference by one
or more of the following
measures:
- Reorient or relocate the
receiving antenna.
- Increase the separation between
the equipment and receiver.
- Connect the equipment into an
outlet on a circuit different from
that to which the receiver is
connected.
- Consult the dealer or an
experienced radio/TV
technician for help.
You are cautioned that any
changes or modifications not
expressly approved in this
manual could void your
authority to operate this
equipment.
Features
The VCT-670RM is a tripod
for video camera recorders.
The Remote Commander
built in the pan handle allows
you to operate (zooming or
recording) the video camera
recorder with a remote C
control jack.
Caution
•After using the tripod,
remove the video camera
recorder and close the legs
and pan handle with facing
out the control switch and
button. Never carry the
tripod with the video
camera recorder attached.
•After the camera recording,
slide the recording standby
switch of pan handle to
LOCK. If you leave it to
STANDBY, the battery will
wear down.
Cleaning
Clean the tripod with a soft
cloth lightly moistened with a
mild detergent solution. After
using the tripod at a location
subject to sea breezes, be sure
to wipe it clean with a dry
cloth.
Identifying the Parts
□
1 Camera mounting shoe
2 Camera mounting screw
and knob
3 Pin
4 Tripod head
5 Pan lock knob
6 Elevator
7 Level
8 Elevator lock knob
9 Elevator height
adjustment crank
10 Leg
11 Stay
12 Camera mounting shoe
lock lever
13 Tripod head lock knob
14 Remote plug
15 Recording start/stop
button '
16 Recording standby switch
17 Photo mode button
18-ZooriT button
19 Pan handle
20 Leg length adjustment
lock lever
Using the Tripod
m Setting the Tripod
1 Spread the legs until the
tripod becomes stable.
2 Press down the stay.
3 Unlock the leg length
adjustment lock levers.
4 Adjust the length of the
legs.
5 Lock the leg length
adjustment lock levers.
B Adjusting the ievei
Adjust the length of the legs
to move the air bubble of the
level into the red circle.
B Adjusting the Height
of the Eievator
1 Loosen the elevator lock
knob.
2 Adjust the height by
turning the elevator
height adjustment crank.
3 Tighten the elevator liKk
knob.
B Mounting the Video
Camera Recorder
Install the battery pack and a
cassette in the video camera
recorder before mounting to
the tripod.
f While pressing the camera
mounting shoe lock lever
fully to the right, slide out
the camera mounting shoe
from the tripod head.
2 Align the pin and the
camera mounting screw
with the holes on the
bottom of the video
camera recorder, and
tighten the screw firmly.
3 While turning the camera
mounting shoe lock lever
fully to the right, replace
the camera mounting shoe
with the video camera
recorder attached into the
tripod head. Then, turn
the camera mounting shoe
lock lever to the left to
lock.
Q Panning and Tilting
Before panning and tilting,
make sure that the elevator
lock knob is locked firmly. If
it is unlocked, it will cause a
camera shake while parming.
Panning
1 Loosen the pan lock knob
to the left.
2 Adjust the position of the
video camera recorder by
moving the pan handle.
3 Tighten the pan lock knob
to the right.
Tilting
4 Turn the pan handle to
the left.
5 Adjust the position of the
video camera recorder by
moving the pan handle.
6 Turn the pan handle to
the right.
Caractéristiques
Le VCT-670RM est un trépied
pour caméscopes. La
télécommande intégrée dans
la poignée de panoramique
vous permet de commander
(zoom ou enregistrement) le
caméscope au moyen d'une
prise
C
de télécommande.
Attention
•Après avoir utilisé le
trépied, détacher le
caméscope et rabattre les
pieds et ta poignée de
panoramique au moyen du
commutateur et de la touche
de commande. Ne jamais
transporter le trépied avec le
caméscope attaché.
•Après l'enregistrement,
faites glisser le
commutateur de pause
d'enregistrement de la
poignee panoramique sur
LOCK. Si vous le laissez sur
STANDBY, la batterie va
s'épuiser.
Nettoyage
Nettoyez le trépied avec un
chiffon doux lejgèrement
imbibé d'une solution de
détergent non agressif. Après
avoir utilisé le trépied dans
un endroit expose aux vents
marins, frottez-le avec un
chiffon sec.
Identification des
composantes
□
1 Sabot de montage de la
caméra
2 Vis et molette de montage
de la caméra
3 Broche
4 Tête du trépied
5 Molette de verrouillage
du panoramique
6 Elévateur
7 Niveau
8 Molette de verrouillage
d'élévateur
9 Manivelle de réglage de
l'élévateur
10 Pied
11 Plateforme
12 Levier de verrouillage du
sabot de montage de la
caméra
13 Molette de verrouillage de
la tête du trépied
14 Fiche de télécommande
15 Touche de commande
d'enregistrement
16 Commutateur de pause
d'enregistrement
17 Bouton de mode photo
18 Commutateur de
commande de zoom
19 Poignée de panoramique
20 Levier de reglage de la
longueur des pieds
Utilisation du
trépied_______________
03 Réglage du trépied
1 Déployez les pieds
jusqu'à ce que le trépied
soit stable.