Attwood Battery Tray with Strap - Manual

Battery
Hold-Down Tray
9092, 9093
Installation Instructions
Attwood marine hardware, navigational lighting, bilge pumps, and
other marine accessories are specified more than any other brand by
America’s best-known boat manufacturers as original equipment.
Look to Attwood for quality replacement parts and marine accessories.
SAVE THESE INSTRUCTIONS
Form Number 69347 Rev. B
03-10
3
®
TOOLS AND MATERIALS REQUIRED FOR INSTALLATION:
• Drill and a suitable drill bit
• Four #10 stainless steel wood/sheet metal pan-head screws
• Four #10 stainless steel flat washers
• Screwdriver
MOUNTING INSTRUCTIONS
CAUTION
Battery must be located in a well-ventilated area to prevent buildup of
explosive gasses. To prevent acid burns, locate in an area away from
casual contact.
1. Determine a suitable location for the battery tray, making sure
there is enough room to work.
2. Using the battery tray as a template, mark the location of the screw
holes.
3. Drill four pilot holes for the screws. Do not drill through the bottom
of the boat.
4. Place the strap in the groove under the tray.
5. Fasten down the tray using the #10 screws and washers.
6. Place the battery into the tray.
7. Fasten buckle over battery.
8. Pull strap ends to secure battery in tray.
9. Make the proper battery connections. The positive terminal should
be insulated to prevent accidental shorting.
ATTWOOD LIMITED WARRANTY
ATTWOOD CORPORATION, 1016 North Monroe, Lowell, Michigan
49331 (“Attwood”) warrants to the original consumer purchaser that
Attwood brand products will be free from defects in materials and
workmanship under normal use and service for one year from the
date of original consumer purchases.
This limited warranty is not applicable if the product has been damaged
by accident, improper installation, unreasonable or improper use, lack
of proper maintenance, unauthorized repairs or modifications, normal
wear and tear, or other causes not arising out of defects in materials
or workmanship.
Attwood products are warranted for use on pleasure boats. Any other
use — including but not limited to commercial, racing, or non-marine
use — are not covered under this warranty. Attwood’s obligation
under this warranty is limited to repair of the product at Attwood’s
plant or replacement of the products at Attwood’s option without
expense to the original consumer purchaser. Any expenses involved
in the removal, reinstallation or transportation of the product are not
covered by this warranty.
The product must be returned to Attwood’s plant at the address
above, postage prepaid, and insured with proof of original purchase
including date. If Attwood is unable to replace the product and repair
is not commercially practical or cannot be timely made, or if the
original consumer purchaser is willing to accept a refund in lieu of
repair or replacement, Attwood may refund the purchase price, less
an amount for depreciation. The acceptance by Attwood of any product
returned or any refund provided by Attwood shall not be deemed an
admission that the product is defective or in violation of any warranty.
Products that are replaced or for which a refund is issued become
the property of Attwood.
THIS WARRANTY IS ATTWOOD’S ONLY EXPRESS WARRANTY
OF THIS PRODUCT. NO IMPLIED WARRANTY SHALL EXTEND
BEYOND ONE (1) YEAR FROM THE DATE OF ORIGINAL
CONSUMER PURCHASE. ATTWOOD SHALL NOT BE LIABLE
FOR ANY DAMAGES FOR LOSS OF USE OF THIS PRODUCT,
NOR FOR ANY OTHER INCIDENTAL OR CONSEQUENTIAL
DAMAGES, COSTS OR EXPENSES.
Some states do not allow limitations on how long an implied warranty
lasts or the exclusion or limitation of incidental or consequential
damages, so the above limitations and exclusions may not apply to
you. This warranty gives you specific legal rights, and you may have
other rights which vary from state to state.
To remove battery–unsnap buckle.
Attwood Battery Hold-Down Tray are designed to be used with
standard batteries (24/24M and 27/27M Series). The tray is made of
non-corrosive, heavy duty black plastic.
Meets ABYC Standard E-10 and U.S. Coast Guard requirements.
Washer •
#10 Screw •
Battery Tray •
Buckle •
Groove •
Strap •
Battery •
© 2003 Attwood Corporation
1016 N. Monroe Street, Lowell, MI 49331-0260 www.attwoodmarine.com