4 system memory support, System memory support, System specification – Kontron KTGM45-mITX User Manual
Page 16
KTGM45 Users Guide
KTD-N0793-O
Page 16
2.4
System Memory support
The KTGM45 board has two DDR3 DIMM sockets and support the following memory features:
•
1.5V (only) 240-pin DDR3 SDRAM DIMMs with gold-plated contacts
•
DDR3-800 (PC3-6400) and DDR3-1066 (PC3-8500)
•
DDR3-800/1066 DIMM with SPD timings supported
•
Unbuffered, single-sided x8/x16 or double-sided x8/x16 DIMMs
•
Supports one or two rank populated DIMM’s.
•
8GB (2x 4GB) max. total system memory using 64-bit OS. (Shared Video Memory is subtracted).
•
4GB maximum total system memory using 32-bit OS. ~3GB is displayed in System Properties.
(Shared Video Memory is subtracted).
•
Minimum total system memory: 512 MB
•
Non-ECC DIMMs
The installed DDR3 SDRAM should support the Serial Presence Detect (SPD) data structure. This allows the
BIOS to read and configure the memory controller for optimal performance. If non-SPD memory is used, the
BIOS will attempt to configure the memory settings, but performance and reliability may be impacted.
Memory Operating Frequencies
Regardless of the DIMM type used, the memory frequency will either be equal to or less than the processor
system bus frequency. For example, if DDR3 800 memory is used with an 800 MHz system bus frequency
processor, the memory clock will operate at 400 MHz. The table below lists the resulting operating memory
frequencies based on the combination of DIMMs and processors.
DIMM Type
Module
name
Memory
Data
transfers
[Mill/s]
Processor
system bus
frequency
[MHz]
Resulting
memory clock
frequency
[MHz]
Peak transfer
rate
[MB/s]
DDR3 800
PC3-6400
800
667
333
5300
DDR3 800
PC3-6400
800
800
400
6400
DDR3 800
PC3-6400
800
1066
400
6400
DDR3 1066
PC3-8500
1066
667
333
5300
DDR3 1066
PC3-8500
1066
800
400
6400
DDR3 1066
PC3-8500
1066
1066
533
8533
Notes: Kontron offers the following memory modules:
•
P/N 1028-6891, DDR3-RAM,
1GB, 240p, 1066MHZ, PC3-8500, DIMM
•
P/N 1030-5722, DDR3-RAM,
1GB, 240p, 1333MHZ, PC3-10600, DIMM
•
P/N 1030-5747, DDR3-RAM,
2GB, 240p, 1066MHZ, PC3-8500, DIMM
•
P/N 1028-6892, DDR3-RAM,
2GB, 240p, 1333MHZ, PC3-10600, DIMM
•
P/N 825534, DDR3-RAM,
4GB, 240P, 1333MHZ, PC3-10600, DIMM
•
Faster RAM than PC3-10600 can be used but will run at lower speed.
Memory Configurations
The KTGM45 boards support the following three types of memory organization:
1. Dual channel (Interleaved) mode. This mode offers the highest throughput. Dual channel mode is enabled
when the installed memory capacities of both DIMM channels are equal. Technology and device width can
vary from one channel to the other but the installed memory capacity for each channel must be equal. If
different speeds DIMMs are used between channels, the slowest memory timing will be used.
2. Single channel (Asymmetric) mode. This mode is equivalent to single channel bandwidth operation. This
mode is used when only a single DIMM is installed or the memory capacities of channel A is bigger than of
channel B. Technology and device width can vary from one channel to the other. If different speeds DIMMs
are used between channels, the slowest memory timing will be used.
3. Flex mode. This mode provides the most flexible performance characteristics and is used if both channels
are populated and at the same time the memory capacities of channel A is smaller than of channel B.
Channel B will be divided into two parts. One part of channel B is used together with channel A and mapped
to dual channel operation. The second part of channel B is mapped to single channel operation.
System specification