Pridiom High Wall Remote Control Manual - Manual (Page 3)

Model
Lowest Voltage of
CPU Emitting Signal
Rated Voltage
R51I7/BG(C)E, R51I8/BG(C)E,
-5 C 60 C( )
8m (when using 3.0 voltage,
it Gets 11m)
3.0V(Dry batteries R03/LR03 2)
2.0V
~ ~
Remote Controller Specifications
1. Operating Mode: AUTO, COOL, DRY, HEAT(Cooling only
model without), and FAN.
2. Timer Setting Function in 24 hours.
O O 3. Indoor Setting Temperature Range : 17 C~30 C(62 F~88 F).
4. Full function of LCD (Liquid Crystal Display)
5. Back light emitting.
Environment
Signal Receiving
Range
Performance Feature
R51I9/BG(C)E;
Function buttons
CAUTIONS
Do not mix old and new batteries or batteries of a different type.
Do not leave the batteries in the remote controller if it is not going
to be used for 2 or 3 months.
Dispose of the old batteries in the special containers to be found
in the sales outlets.
1 TEMP UP Button
Push this button to increase the indoor temper-
o o ature setting in 1 C(2 F) increments to 30 C(88 F).
2 TEMP DOWN Button
Push this button to decrease the indoor temper-
o o ature setting in 1 C(2 F) increments to 17 C(62 F).
Model: R51I5/BG(C)E,
R51I6/BG(C)E,
R51I7/BG(C)E,
R51I8/BG(C)E.
ION and FOLLOW button:
Optional function.
Each time the button is pressed, the operation
mode is selected in the sequence of the following:
3 MODE Button
3 3 4 4
TEMP
AUTO
COOL
DRY
HEAT FAN
HIGH
MED
LOW
MODE FAN SPEED
SWING TIMER ON ECONOMY
ON/OFF
TIMER OFF RESET LOCK
1 2
4
5
6
3
8
7
9
10
11
12
13
SET TEMPERATURE( C)
FOLLOW
ME LED
DISPLAY
14
ION
TURBO
15
4 SWING Button
Used to stop or start louver movement and
set the desired up/down airflow direction.
When push this button, the ion generator is
energized and will help to remove pollen and
impurities from the air.
5 ION Button(Optional)
6 FOLLOW ME Button(Optional)
Push this button to initiate the Follow Me
function, the remote controller begins to detect
the actual temperature at its location. The
remote controller will send this signal to the
air conditioner every 3 minutes interval until
press the Follow Me button again. The air
conditioner will beep to indicate the Follow Me
feature has ended if it does not receive the
signal during any 7 minutes interval.
7 RESET Button
Once the recessed RESET button is pressed,
all of the current settings will be cancelled
and the controller will return to the initial settings.
8 ON/OFF Button
Operation starts when this button is pressed
and stops when the button is pressed again.
NOTE: Heat mode is for Cooling & Heating models only.
AUTO COOL DRY HEAT FAN
Used to select the fan speed in four steps:
Auto Low Med High
FAN SPEED Button
10 TIMER ON Button
9
Press this button to activate the Auto-on time
setting. Each press will increase the time setting
R51I10/BG(C)E, R51I11/BG(C)E, R51I12/BG(C)E;
O O -41 F~140 F
NOTE:
Temperature setting display:
Celsius scale( C):
Fahrenheit scale( F):
R51I5/BG(C)E, R51I6/BG(C)E,
R51I9/BG(C)E; R51I10/BG(C)E, R51I11/BG(C)E, R51I12/BG(C)E.
R51I5/BG(C)E, R51I6/BG(C)E,
R51I7/BG(C)E, R51I8/BG(C)E,