Universal Remote Control (URS) UR4U-MDVR-CHD2 - Manual

A. Quick Set-Up Method
STEP1 Turn on the component you want to
program. To program your TV, turn on the TV.
STEP2 Press and hold the [DEVICE] key for 5
seconds until the Device LED will blink
once and stays on. Continue to hold the
[DEVICE] key and press the number key
assigned to your brand in the Quick Set-
up Code Table and release both
[DEVICE] key and the number key to
save the code. The Device LED will blink
twice to confirm that the code is stored.
STEP3 Point the remote control at the
component.
STEP4 Press the power button. If it turns off, it is
programmed for your component. If it
does not turn off, use the Pre-
Programmed 3-Digit code Method or
Scanning Method.
Repeat the steps above for all components
(TV,DVD, AUX).
B. Quick Set-up Code Tables
C. Pre-Programmed 3-Digit Code Method
STEP1 Turn on the Component you want to
program (TV, DVD or AUX) .
STEP2 Press the [COMPONENT] button (TV,
DVD or AUX) to be programmed and
[OK/SEL] button simultaneously for 3
seconds. The Component LED will light
Manufacturer/Brand Quick Number
TV
0 SANYO
1 SONY
2 SAMSUNG
3 LG
4 TOSHIBA
5 PANASONIC
6 PHILIPS
7 HITACHI
8 SHARP
9 VIZIO
Manufacturer/Brand Quick Number
DVD
0 HITACHI
1 SONY
2 PHILIPS
3 SAMSUNG
4 PHILIPS MAGNAVOX
5 PANASONIC
6 LG
7 JVC
8 DENON
9 PIONEER
Manufacturer/Brand Quick Number
AUX
0 BOSE
1 HP
2 ONKYO
3 APPLE/iPod
4 MICROSOFT / XBOX
5 SONY / PS2
6 LUTRON
7 X-10
8 YAMAHA
9 ROKU
Button Functions
4
Programming the Remote Control
5
G
There are three ways you can program your remote control:
* Quick Set-Up Method
* The Pre-P
rogramm rogrammed 3-Digit Code Method
* The Auto-Search Method
The Quick Set-Up Method is a unique new feature that enables the fastest and easiest set-up by using
one-digit codes for up to 10 major brands for each component.
The Pre-Programmed Code Method allows you to setup all the buttons at once by entering 3-digit code
numbers that correspond to a particular Component’s manufacturer/brand, so it’s the fastest and
easiest of the two methods. (Code Tables are on the backside of this Instruction Sheet.) The Auto-
Search Method scans through all the codes in the remote control, one at a time.
IMPORTANT SETUP NOTES:
This pertains to all programming steps. When you are in setup mode in each component, a component
LED will light up for 30 seconds. If you do not press a button within 30 seconds, the LED light will turn off
and exit setup mode and you will need to start over.
When programming a combo unit, program as a DVD first.
for 30 seconds indicating the unit is
ready to be programmed.
STEP3 Point the remote control toward the
Component and enter the 3-digit code
number assigned to your brand.
*Note : If the 3-digit code number you just
entered is correct, the Component will
turn Off. If it did not turn Off, continue
entering code numbers listed for that
brand until the Component turns Off.
STEP4 After you’ve entered the correct code
number and the Component has turned
Off, press the [POWER] button to turn
the Component back On. Now it’s time
to test the VOLUME and MUTE buttons
for the TV (or PLAY and STOP buttons
for DVD) to make sure they all work. If
any of the functions do not work as
they should, repeat from STEP 3 using
the next 3-digit code number listed for
that brand.
STEP5 Once you have found the correct 3-
digit code, save it by pressing the same
[COMPONENT] button one more time.
The Component LED light will blink
twice to confirm that the code was
successfully stored.
Now, program the rest of your Components by
repeating STEPS 1-5.
*Note : If the Pre-Programmed Method did
not work, or if the Code Tables do not
list your Component brand, use the
Auto-Search Method as explained in
Section D.
D. Auto-Search Method
STEP1 Turn on the Component you want to
program (TV, DVD or AUX).
STEP2 Press the [COMPONENT] button (TV,
DVD or AUX) to be programmed and
[OK/SEL] button simultaneously for 3
seconds. The Component LED will light
for 30 seconds indicating the unit is
ready to be programmed.
STEP3 Point the remote toward the
Component and press the [CH 5] or
[CH 6] button one step at a time or
keep it pressed. The remote will emit a
series of ON/OFF commands. Release
the [CH
5] or [CH6] button as soon as
the Component turns Off.
STEP4 Test functions. (Same as for 3-Digit Code
Programming Method - Section C). If any
of the functions do not work as they
should, repeat from STEP 3 using [CH
5]
or [CH 6] buttons to find the correct code.
STEP5 Save the code. (Same as for 3-Digit Code
Programming Method - Section C).
Now, repeat the Auto-Search Method for those
Components you could not program earlier with the
Pre-Programmed Method.
E. Finding a Component Button’s
Setup Code Number
If you used the Auto-Search Method to program a
Component, you may not know what the correct code
number is. Here is a way for you to identify the code
number, so you can record it for future reference.
STEP1 Press the [COMPONENT] button (TV, DVD or
AUX) you want to verify and the [OK/SEL]
button simultaneously for 3 seconds. The
Component LED will light for 30 seconds.
STEP2 Press the [INFO] button and count the
number of times the Component LED light
blinks. This number indicates the first digit
of the code, followed by the second and
third, each separated by a one second
pause when the LED will turn off.
*Note : 10 blinks represents the number zero.
Example : One blink, (pause), eight blinks, (pause) and
three blinks, indicates code number 183.
F. AUX Function: Programming a 4 th
Component
You can take advantage of the AUX function to
program a 4
th Component such as a second TV, DVD
or Audio Component.
STEP1 Turn on the 4 th Component you want to
program (TV, DVD or Audio).
STEP2 Press the [AUX] button and the [OK/SEL]
button simultaneously for 3 seconds.The
[AUX] Component LED will light for 30
seconds.
STEP3 Press the [COMPONENT] button you want
to setup. Point the remote control toward
the Component and enter the 3-digit code
number assigned to your brand.
*Note : If the 3-digit code number you just entered is
the correct number, the Component will turn
Off. If it did not turn Off, continue entering
code numbers listed for that brand until the
Component turns Off.
STEP4 Test functions. (Same as for 3-Digit Code
Programming Method - Section C). If
any of the functions do not work as they
should, you need to find a new code.
STEP5 Once you have found the correct 3-digit
code, save it by pressing the [AUX] button
one more time. The Component LED light
will blink twice to confirm the code was
stored. Now when you press the AUX
button, all the buttons will work with that 4
th
Component.
Universal Remote Control, Inc.
www.universalremote.com
OCE-0053A REV 28 (14/05/23)
UR4U-MDVR-CHD2
Operating Instructions
For 4-Function
Cable Remote Control
This remote control is designed to operate all
Motorola and Scientific Atlanta digital set top
boxes (including HD and DVR), plus the
majority of TVs, DVDs and AUDIO equipment
on the market as shown below.
CABLE : Cable Converters TV : Televisions
DVD : DVDs, TV/DVDs
AUX : Audio Receivers and DVRs, etc.
Introduction
1
DEFAULT STATUS:
Component Default: CABLE
Channel Default: CABLE channel +/- and
numbers operate through the CABLE box.
You have the option of controlling channel +/-
and numbers through the TV or DVD. Refer to
section H for programming steps.
Volume Default: CABLE volume +/- and mute
operate through the TV. You have the option
of controlling volume through the Cable box
or DVD. Refer to section I for programming
steps.
Operations
3
Replacing Batteries
2
Before you program or operate this remote
control, you must first install two new AA Alkaline
batteries.
STEP1 Remove the battery compartment cover
on the back of your remote control.
STEP2 Check battery polarity carefully, and
install the batteries as shown in the
illustration below.
STEP3 Replace the battery compartment cover.
G. Programming the System On/Off Button
This allows you to program the System On/Off button
so it can send up to four power On/Off commands
with one button press.
STEP1 Press the [CBL] button.
STEP2 Press the [SYSTEM ON/OFF] button and the
[OK/SEL] button simultaneously for 3
seconds. The [CBL] Component LED will
light for 30 seconds.
STEP3 Press the first [COMPONENT] button you
want to store in the [SYSTEM ON/OFF]
button and then the [POWER] button.
Repeat this for other Components until you
have stored all the desired power
commands into the [SYSTEM ON/OFF]
button.
STEP4 Press the [CH
5] button to save the power
commands you stored. The [CBL] button
will blink twice to confirm the commands
have been saved.
H. Programming Channel Control
You can program the channel controls (Channel Up,
Channel Down, Last and Numbers) from one
Component to operate in another Component mode.
Default channel control settings on the remote control
are as follows:
CBL : CBL T V : CBL
DVD : DVD AUX : AUX
If you wish to operate the TV channel control in TV
mode, use the following steps.
STEP1 Press the [TV] button and the [OK/SEL]
button simultaneously for 3 seconds. The
[TV] Component LED will light for 30 seconds.
STEP2 Press the [VOL
6] button.
STEP3 Press the [TV] button again.
The Component LED will blink twice to
confirm the programming.
To return to original state:
If you wish to restore the CABLE channel control in
TV mode, repeat the above steps but press [CBL]
in
STEP3.
I. Programming Volume Control
You can program the volume controls (Volume Up,
Volume Down and Mute) from one Component to
operate in another Component mode. Default volume
control settings on the remote control are as follows:
CBL : TV T V : TV
DVD : TV AUX : AUX
If you wish to operate the CBL volume control in
CBL mode, use the following steps.
STEP1 Press the [CBL] button and the [OK/SEL]
button simultaneously for 3 seconds. The
[CBL] Component LED will light for 30
seconds.