Casio DQ-961 - Manual (Page 2)

Operation Guide DQ-960/961
2
• Holding down UP (+) or DOWN (–) changes the flashing digits at high speed.
• You can set the year in the range of 2000 to 2039. The day of the week is set automatically in accordance with
the date setting.
• Pressing UP (+) or DOWN (–) while the Time Setting Screen is on the display causes the seconds count to be
reset to 00.
• Each press of UP (+) or DOWN (–) while the 12-hour/24-hour Timekeeping Screen is on the display toggles
between 12-hour and 24-hour timekeeping.
3. After making the settings you want, use the SET button (5) to display the Normal Timekeeping Screen.
• The clock automatically returns to the Normal Timekeeping Screen if you leave a setting screen on the display for
about three minutes without performing any operation.
USING THE ALARM
The alarm sounds and the light turns on when the alarm time you set is reached. You can also use the Alarm Mode
selector (2) to select the snooze alarm feature.
Setting the Alarm Time
Use the DOWN (–) and UP (+) buttons (3) to set the alarm time.
Pressing the DOWN (–) and UP (+) buttons (3) causes the alarm time to appear in place of the date on the
display.
UP ( + ) DOWN (—)
RESET
T E M P.
MAX/MIN
HUMIDITY
MAX/MIN UP
(+) DOWN
(–)
SET CLEAR
°C / °F
Press to change the
alarm time setting (+) Press to change the
alarm time setting (—)
Press to change the
alarm time setting (+) Press to change the
alarm time setting (—)
DQ-960
DQ-961
• Holding down UP (+) or DOWN (–) changes the digits at high speed.
Turning the Alarm On and Off
Use the Alarm Mode selector (2) on the side of the clock to turn the alarm on and off, and to select the snooze
feature.
• The alarm time appears in place of the date on the display whenever the Alarm Mode selector (2) is set to ON
or SNZ.
• The light also turns on for the first four seconds that the alarm sounds.
• The volume of the alarm sound cycles through five levels as it sounds.
Stopping the Alarm
• When alarm is sounding, press the SNOOZE/LIGHT button (1) to stop it. When the snooze feature is turned on,
the alarm will sound again in about five minutes.
• To turn off the snooze feature, slide the Alarm Mode selector (2) to OFF.
GENERAL GUIDE
1 1 1 1 1 SNOOZE/LIGHT button
• Press this button to illuminate the display for about four seconds.
• Pressing this button while the alarm is sounding stops the alarm.
2 2 2 2 2 Alarm Mode selector
SNZ: Snooze alarm on
ON: Alarm on
OFF: Alarm off
3 3 3 3 3 UP (+) / DOWN (–) buttons
Use these buttons to change the alarm time or the setting that is flashing on the display.
4 4 4 4 4 ° C/ ° F button
Press this button to toggle the temperature units between Celsius and Fahrenheit.
5 5 5 5 5 SET button
Use this button when setting the current time.
6 6 6 6 6 CLEAR button
Press this button to clear the currently displayed high/low temperature or humidity.
7 7 7 7 7 MAX/MIN TEMP. button
Press this button to display the high and low temperature values.
8 8 8 8 8 RESET button
Press this button to reset the clock after replacing its batteries.
9 9 9 9 9 MAX/MIN HUMIDITY button
Press this button to display the high and low humidity values.
USING THE CLOCK
1. Press the SET button (5) to cycle through the setting screens as shown below.
12-hour/24-hour
Timekeeping Screen Time Setting Screen Month and Day Setting Screen Year Setting Screen
Normal Timekeeping Screen
2. While the screen you want is displayed, use the DOWN (–) and UP (+) buttons (3) to change the flashing
digits.
UP ( + ) DOWN (—)
RESET
T E M P.
MAX/MIN
HUMIDITY
MAX/MIN UP
(+) DOWN
(–)
SET CL EAR °C / °F
Press UP (+) to increase
the flashing digits.
Press DOWN (–) to decrease
the flashing digits.
Press UP (+) to increase
the flashing digits.
Press DOWN (–) to decrease
the flashing digits.
DQ-960
DQ-961
Alarm Mode selector
SNZ
ON
OFF
Description
The alarm sounds at the preset time for one minute, and seven more times every five
minutes thereafter. Even if you stop the alarm by pressing the
SNOOZE/LIGHT
button (1), the alarm sounds again five minutes later.
• The indicator flashes on the display to indicate that the snooze feature is
activated.
The alarm sounds at the preset time for one minute.
The alarm does not sound.