Panasonic SC-DT300 - Manual (Page 36)

Disc handling
Do not use irregularly shaped discs, such as heart-shaped.
(These can damage the unit.)
■ How to hold a disc
Do not touch the recorded surface.
©
■ If the surface is dirty
Wipe it with a damp cloth and then wipe dry.
■ If the disc is brought from a cold to a warm envi­
ronment, moisture may form on the disc
Wipe with a soft, dry, lint-free cloth before using the disc.
■ Handling precautions
• Do not write on the iabet side with a bail-point pen or other writing
instrument.
• Do not use record cleaning sprays, benzine, thinner, static electric­
ity prevention liquids or any other solvent,
• Do not attach labels or stickers to discs. (Do not use discs with
exposed adhesive from tape or left over peeled-off stickers.)
• Do not use scratch-proof protectors or covers.
• Do not use discs printed with label printers available on the market.
■ Do not place or store discs in the following places
• Locations exposed to direct sunlight
• Humid or dusty locations
• Locations directly exposed to a heat vent or heating appliance
Glossary
8
C
S
tc
Bitstream
This is the digital form of multiple channel audio data (e.g., 5.1 chan­
nel) before it is decoded into its various channels.
Decoder
A decoder restores the coded audio signals on DVDs to normal. This
is called decoding.
Dolby Digital
This is a method of coding digital signals developed by Dolby Labo­
ratories. Apart from stereo (2-channel) audio, these signals can also
be 5.1-channel audio. A large amount of audio information can be
recorded on one disc using this method.
Dolby Pro Logic
A surround system where a 4-channel audio track is recorded as
2 channels and then is restored to 4 channels for play. The surround
channel is monaural and can reproduce up to 7 kHz.
DTS (Digital Theater Systems)
This surround system is used in many movie theaters around the
world. There is good separation between the channels, so realistic
sound effects are possible.
Dynamic range
Dynamic range is the difference between the lowest level of sound
that can be heard above the noise of the equipment and the highest
level of sound before distortion occurs.
Film and video
DVDs are recorded using either film or video. Usually, film is record­
ed at 24 frames per second, the rate movies are filmed at, while
video is recorded at 30 frames per second.
Frame stilt and field still
Frames are the still pictures that go together to make a moving pic­
ture. There are about 30 frames shown each second.
One frame is made up of two fields. A regular television shows these
fields one after the other to create frames.
A Still is shown when you pause a moving picture. A frame still is
made up of two alternating fields, so the picture may appear blurred,
but overall quality is high.
A field still is not blurred, but it has only half the information of a
frame still so picture quality is lower.
RQT6534
Interlace and progressive output
NTSC, the video signal standard, has 480 interlaced (i) scan lines,
whereas progressive scanning uses twice the number of scan lines.
This is called 480p.
The 480i video signals output from this unit's COMPONENT VIDEO
OUT terminals (Y, P b , P r ) allow you to enjoy higher quality pictures
than if the signals were output from the video output terminal or S-
VIDEO OUT terminal. The COMPONENT VIDEO OUT terminals are
also able to handle 480p (progressive) video signals which are of
even greater resolution.
t/P/B
MPEG 2, the video compression standard adopted for use with
DVD-Video, codes frames using these 3 picture types.
I: Intra coded picture (l-picture)
This is the standard picture and is a complete picture in itself.
This means it has the best picture quality and is the best to use
when adjusting the picture.
P: Predictive coded picture (P-picture)
This picture is calculated based on past 1 or P-pictures.
B: Bidirectionally-predictive coded picture (B-picture)
This picture is calculated by comparing past and future I and
P-pictures so it has the lowest volume of information.
Linear PCM (pulse code modulation)
These are uncompressed digital signals, similar to those found on
CDs.
MP3
A method of compressing audio, MPEG Audio Layer 3 (MP3) allows
audio to be reduced to up to one tenth its original size without overtly
hurting audio quality.
When creating MP3 files to play on this unit
• Disc formats: ISO9660level1 and level 2 (except for extended for­
mats)
Files: MP3 files with the suffix “.mp3" or “.MP3"
•To have this unit play files in a certain order, prefix folder and file
names with numbers in the order you want to play them. This may
not work in alt cases.
Not compatible with multi-session recordings
If you record MP3 onto CD-R/CD-RW over a number of sessions,
this unit can play only the recordings made in the first session.
Playback control (PBC)
If a Video CD has playback control, you can select scenes and infor­
mation with menus.