Panasonic KX-TG9150E - Manual (Page 26)

Multi-unit Operation Multi-unit Operation
Operating additional units
Additional handsets
up to 6 handsets can be registered to a
single base unit.
Important:
• The additional handset model
recommended for use with this unit is
noted on page 4. if other model handset is
used, certain operations (handset
settings, base unit settings, etc.) may not
be available.
• Additional handsets will give you the
freedom to, for example, have an intercom
call with another handset while a third
handset is on an outside call.
Additional base units
Handsets can be registered to up to 4 base
units, allowing you to add additional base
urrits and extend the area in which your
handset(s) can be used. If a handset moves
out of range of its base unit when “Auto” is
selected on base unit selection (page 51), it
will look for another base unit to make or
receive calls. A base unit and the handsets it
communicates with is called a “radio cell”.
Note:
• Calls will be disconnected when the
handset moves from one radio cell to
another.
Registering a handset to a
base unit
The included handset and base unit are
preregistered. If for some reason the
handset is not registered to the base unit (for
example, T flashes even when the handset
is near the base unit), register the handset
manually (page 50).
To register an additional handset to a
base unit (easy registration)
After purchasing an additional handset,
register it to the base unit. Ensure that the
additional handset is switched on. If it is not
on, press and hold |7i©| for few seconds
to turn the handset on,
1 Lift the additional handset and press
[7^®] to put the handset in standby
mode.
2 Press and hold [•«] on the base unit for
about 3 seconds, until the registration
tone sounds.
3 Place the additional handset on the
base unit. The registration tone
continues to sound. With the handset
still on the base unit, wait until a
confirmation tone sounds and T stops
flashing.
Note:
• If an error tone sounds, or if T is still
flashing, register the handset manually
(manual registration; page 50).
• If all registered handsets start ringing in
step 2, press [♦»))! to stop. Start again from
step 1.
• Charge the batteries of your additional
handset for about 7 hours before initial
use.
• This registration method cannot be used
for handsets that have already been
registered to a base unit. Register the
handset manually (manual registration;
page 50).
To register a handset to an additional
base unit (manual registration)
You can register a handset to a base unit
manually using the following method.
1 IS (centre of joystick) | gg
2 “Registration” —>■ 5HI
3 “Register H.set"—> Mli
4 Select a base unit number. ^3
• This number is used by the handset
as a reference only.
5 Press and hold on the base unit for
about 3 seconds, until the registration
tone sounds.
• If all registered handsets start ringing,
press [*>1)1 to stop, then repeat this
step,
• After pressing [*>))], the rest of this
procedure must be completed within 1
minute.
6 Wait until “Enter Base PIN” is
displayed, then enter the base unit PIN
(default: “0000”), then press B!3.
• When the handset has been
registered successfully, T will stop
flashing. If keytones are turned on
(page 32), a confirmation tone will be
heard.
Selecting a base unit
When “Auto” is selected, the handset will
automatically use any available base unit it
is registered to. When a specific base unit is
selected, the handset will make and receive
calls using that base unit only. If the handset
is out of range of that base unit, no calls can
be made.
1 13 (centre of joystick) ^ i ^ ^3
2 “Select Base” —> ^3
3 Select the desired base unit number, or
“Auto”, —^ Kin
• The handset starts searching for the
base unit.
Cancelling a handset
A maximum of 6 handsets can be registered
to a base unit, A handset can cancel its own
registration (or the registration of another
handset) that is stored in the base unit. This
will allow the base unit to “forget" the
handset.
1 El (centre of joystick) ^ —> S3
2 Enter “335",
3 “Cancel Handset”—> EI3
• All handsets registered to the base
unit are displayed.
4 Select the handset(s) you want to
cancel. —> KM
• The selected handsets are indicated
by a ’V”.
• To cancel a selected handset, press
Wam again.
5 ^ “Yes” —^ ISIl
• “Flease Wait . . . ” will be displayed
and a long beep will sound.
• The handset does not beep when
cancelling its own registration.
6 [ J ^ m
Cancelling a base unit
A handset can be registered to a maximum
of 4 base units. A handset can cancel a base
unit that it is registered to. This allows the
handset to “forget” the base unit.
1 (centre of joystick) —>• | —> S3
2 “Registration" — t a i
3 Enter “335”,
4 “Cancel Base” —> t»£l
5 Select the base unit(s) you want to
cancel. —> BM
• The selected base unit number(s) are
indicated by a ‘V’’.
• To cancel a selected base unit
number, press again.
6 ia ^ “Yes” ->
• A long beep will sound.
7 [7^©]
Note:
• To register the handset to another base
unit or to the same base unit again, see
manual registration (page 50).
50 Helpline Tel. No.: U.K. 08700 100 076 R.O.I. 01289 8333 Helpline Tel, No.; U.K. 08700 100 076 R.O.I. 01289 8333 51