Panasonic SL-SX340 - Manual (Page 2)

Power Supply Preparations
Refer to the specifications (page 6) for information on operating times when using dry cell batteries.
Using the AC adaptor
I SL-SX390 [F^l;^SX34d i
Use only the included AC adaptor. Use other adaptors
can damage the unit.
Be sure to obtain the optional AC adaptor (RFEA403B-S),
Connect the AC adaptor.
DC IN jack (DC IN 4.5 V )
•Turn the unit off before connecting or disconnecting
the AC adaptor.
•The unit is in the standby condition when the AC
adaptor is connected. The primary circuit is always
“live” as long as the AC adaptor is connected to an
electrical outlet.
Using rechargeable batteries
(not included)
• If rechargeable batteries are to be used, rechargeable
batteries manufactured by Panasonic are recommended.
•This unit cannot recharge batteries. The battery indi-
cator will not function correctly when using recharge­
able batteries.
Using dry cell batteries
(not included)
Insert two ‘‘LR6, AA, UM-3” alkaline bat­
teries.
If the battery lid
comes loose
Slide the lid back into
place horizontally.
Removing batteries
Push up on the battery
in the direction indicat­
ed by the arrow. Then
lift it out.
The dry cell batteries should be changed when the unit
is off.
If the unit malfunctions or freezes during use,
disconnect the power source (the AC adaptor
or batteries).
Re-connect the power source and continue op­
eration.
Bottery indicator
Battery indicator —i
This indicator flashes when the batteries are almost out
of power. Power is cut off completely a short while later.
Replace batteries with new ones.
The length of time the unit will continue to operate be­
tween when the battery indicator starts flashing and
when the power is cut off differs depending on the type
of batteries used.
Using the car adaptor
The SL-SX361C comes with a car adaptor. Be sure to
use the adaptor specially designed for this model.
(Refer to the separate “Installation Instructions",)
Use only the recommended car adaptor. Use of other
car adaptors can damage the unit.
Be sure to obtain the car adaptor (SH-CDC9) for SL-
SX390 and SL-SX340, available as an optional acces­
sory.
Location of Controls
m Back panel of the unit
ET
Portable CD Player El Wired remote control
O Stop/operation off button (■)
O Skip/search buttons
(!◄◄, ►►!)
0 Headphone volume control
buttons (“,VOL, +)
0 EQ button (EQ)
0 Display
O Mode button (MODE)
0 Memory/recall button
(MEMORY/RECALL)
0 Play/pause button {^/11)
O Open switch (OPEN P*)
O Headphone jack (Q)
0 Hold switch (HOLD)
0 Hole for car mounting base
0 DC IN jack
(DC IN 4.5 V )
0 CD release button (PUSH)
O Skip/search buttons
i \ « , ►►!)
0 PIay/stop/operation off button
(■/►)
G Volume control buttons
(",VOL,+)
0 Headphone jack/ earphone
jack
0 Clip
O Hold switch (HOLD)
0 EQ button (EQ)
0 Plug
HOLD Function
This function causes the unit to ignore
short, accidental button presses. (The
disc lid can still be opened and closed.)
The HOLD function prevents the
following:
•The unit is powered on accidentally
when not in use, causing the batteries
to run down.
•A button is accidentally pressed during
play, interrupting the operation.
I SL-SX390 I
You still can operate the unit with the re­
mote control when the main unit's HOLD
function is on and vice versa.
To use the HOLD function
Set [HOLD] to the HOLD position.
“ho I d” indication
When the unit is in HOLD mode, press­
ing any button causes the indication
"ho I d" to appear on the display.
When the unit is powered off
The “ha 1 d" indication appears only
when [^/||] is pressed.
Before operating the buttons
Be sure to move [HOLD] to release
the unit from the HOLD mode.