Inovonics EN1215EOL - Manual (Page 2)

2.5 Register the EN1215EOL
Transmitters must be registered with the system in order
to be monitored and supervised. When supervised, the
transmitter will send a check-in message to the receiver
every three minutes. Each transmitter has a unique
factory-programmed identification number.
Refer to the receiver installation instructions for details on
registering a transmitter.
1. When prompted by the receiver to reset transmitter,
press the Reset button (Figure 1).
2. Replace the cover.
3. Test the transmitter and ensure appropriate response.
2.6 Mount the EN1215EOL
1. Route the external wiring through the wall, as shown
in Figure 5.
2. Mount the transmitter to the wall using the the wall-
mount screw holes (Figure 1), ensuring the housing is
flush against the wall and the wall tamper switch is
firmly depressed.
Figure 5 Mount the Transmitter to the Wall
3. Close the housing.
4. Secure the housing through the enclosed housing
screw hole (Figure 1). Accessing this screw on an
active transmitter requires opening the housing and
removing the battery, causing a tamper condition.
3 Specifications
Note: A 2.2K ohm resistor is required to operate the
EN1215EOL.
Dimensions: 3.5x1.7x0.9" (89x43x23 mm)
Weight: 3 oz (85g)
External contacts: N/O or N/C
Distance, external contact to EN1215EOL: 10 feet (3
meters) maximum
Power requirement: 3 VDC, 60 mA
Typical battery life: 3-5 years
Battery type (BAT604): Panasonic CR123A
Operating environment: 0 to 60°C (32 to 140°F), 90%
relative humidity, noncondensing
Note: Specifications and data are subject to change
without notice.
UL listings: UL 365, UL 1023, ULC/ORD-C1023-74, UL
1076, UL 1610.
Compatible UL receiver: EN4216MR, EN4232MR,
EN7285
4 Television and Radio Interference
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
5 FCC Part 15 and Industry Canada
Compliance
This device complies with part 15 of the FCC Rules and
Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.
6 Warranty/Disclaimer
Caution: Changes or modifications not expressly
approved by the party responsible for compliance could
void the user's authority to operate the equipment.
Inovonics Wireless Corporation ("Inovonics") warrants its
products ("Product" or "Products") to conform to its own
specifications and to be free of defects in materials and
workmanship under normal use for a period of thirty-six
(36) months from the date of manufacture. Within the
warranty period, Inovonics will repair or replace, at its
option, all or any part of the warranted Product. Inovonics
will not be responsible for dismantling and/or
reinstallation charges. To exercise the warranty, the User
("User", "Installer" or "Consumer") must work directly
through their authorized distributor who will be given a
Return Material Authorization ("RMA") Number by
Inovonics. Details of shipment will be arranged directly
through the authorized distributor.
This warranty is void in cases of improper installation,
misuse, failure to follow installation and operating
instructions, alteration, accident or tampering, and repair
by anyone other than Inovonics.
This warranty is exclusive and expressly in lieu of all
other warranties, obligations or liabilities, whether written,
oral, express, or implied. There is no warranty by
Inovonics that Inovonics product will be merchantable or
fit for any particular purpose, nor is there any other
warranty, expressed or implied, except as such is
expressly set forth herein. In no event shall Inovonics be
liable for an incidental, consequential, indirect, special, or
exemplary damages, including but not limited to loss of
profit, revenue or contract, loss of use, cost of down time,
or interruption of business, nor any claim made by
distributor's customers or any other person or entity.
This warranty will not be modified or extended. Inovonics
does not authorize any person to act on its behalf to
modify or extend this warranty. This warranty will apply
only to Inovonics Products. Inovonics will not be liable for
any direct, incidental or consequential damage or loss
whatsoever, caused by the malfunction of Product due to
products, accessories, or attachments of other
manufacturers, including batteries, used in conjunction
with Inovonics Product.
Wall Tamper
Switch