Awntech Savannah Series - Manual (Page 2)

Due to the fact that there is such a variety of building wall surfaces,
Awntech does not supply the hardware to install your awning. You will
need to purchase installation hardware at your local do-it-yourself center.
We have advised you on different surface applications below:
CONCRETE BLOCK WALLS: (1) ½” masonry bit with a 3/8” shank, (4-5) 5/16”x 3”
masonry anchor bolts, 9/16” socket. You will also need a roll of weather stripping.
METAL BUILDINGS: (1) 2x6x8 #2YP cut into 12” blocks for the back side of the metal,
(4-5) 5/16”x 4” lag bolts, (4-5) 5/16” washers, rubber installation strips (in the shape of
the metal) and a 3/8” drill bit. Bolt through the washer, the bracket and the metal into
wood blocks behind the metal. Before tightening the bracket insert the rubber strips
between the building and the awning.
ANY TYPE OF SIDING: (4-5) ¼”x 4” toggle bolts, (4-5) ¼” washers, (1) Flat head
screwdriver (1) ½ drill bit (or if you hit a stud): (5-8) 5/16”x4” lag bolts, (4-5) 5/16”
washers, (1) 3/16” drill bit and a 9/16” socket. You will also need a roll of weather
stripping.
CONCRETE, BRICK OR STONE: (1) ½ masonry bit with a 3/8” shank, (4-5) 5/16”x 3”
masonry anchor bolts, (4-5) 5/16”x1/4” bushings, 9/16” socket. You will also need a roll
of weather stripping.
STUCCO: (4-5) ¼”x 4” toggle bolts, (4-5) ¼” washers, (1) Flat head screwdriver (1) ½
drill bit (or if you hit a stud): (4) 5/16”x4” lag bolts, (4-5) 5/16” washers, (1) 3/16” drill bit
and a 9/16” socket. You will also need a roll of weather stripping
.
• Please read the instructions fully before assembly.
• This awning is designed to be assembled on the wall.
Parts List:
Size 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19
Top Bar - C Channel TB 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2
Front Bar FB 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2
Cover Support CVS 3 3 3 5 5 5 5 5 5 5 5 5 7 7 7 7 7 7
Projection P 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
Back Bar B 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
Projection Bar Assembly PA 1 1 1 3 3 3 3 3 3 3 3 5 5 5 5
Other parts Self tapping screws, Z-brackets
Tools Required: Electrical Drill, ¼” Nut Driver Bit, Full Socket Set, Full set of Steel
and Masonry Bits, Tape Measure, Safety Glasses, 4’ Level, A Safe Ladder, #2 Pencil
YOU MAY ALSO NEED AN ASSISTANT FOR LARGER AWNINGS. IT DEPENDS ON
THE SIZE AND WEIGHT OF THE AWNING.