Braeburn 5000 - Manual (Page 5)

8
1. Place the system switch in the HEAT
mode of operation.
2. Press the PROG button to enter the Program
setting mode.
MORN set point of the
Weekday Program Group will be displayed.
The display will show
M, TU, W, TH, F to
indicate the Weekday group is being
programmed. The hour and the AM/PM indicator will be flashing.
3. Press the or button to change the time to the desired hour in one hour
increments. Press the PROG button. The minute portion of the set point time
will begin flashing.
4. Press the or button to change the time to the desired minute in 10-minute
increments. Press the
PROG button. The SET temperature will begin flashing.
5. Press the or button to change the set point temperature to the desired
setting in 1º (.05˚ C) increments. Press the
PROG button. The thermostat will
now display the DAY set point time and temperature. Again, you will see the
hour and the AM/PM indicator flashing.
6. Follow steps 3 through 5 to set the set point times and temperatures for the
periods of DAY, EVE and NIGHT.
7. After pressing the PROG button, you will enter the Weekend Program Group.
The display will show
SA, SU to indicate the Weekend Group is being
programmed. The hour portion of the MORN set point time and the AM/PM
indicator will be flashing.
8. Follow steps 3 through 6 to set the set point time and temperatures for the
periods of MORN, DAY, EVE and NIGHT.
9. Place the system switch in the COOL mode of operation. The display will show
COOL. Follow steps 2 through 8 to program the set point times and tempera-
tures
for the Weekday and Weekend groups in the COOL mode.
NOTE: To erase all entered programs, current time of day, day of week and other
user settings, gently press the RESET button using a paper clip or a small pencil tip.
This will return all thermostat settings to their default values.
Entering Your Program – 7 Day Mode
The 7 Day mode has separate Whole Week or Individual Day programming to allow
you to change the daily set point times and temperatures to meet your individual
schedule needs. The Whole Week programming can be used to set the main portion
of your schedule, allowing you to later modify specific days of the week as required
using the Individual Day programming capabilities.
Whole Week - allows you to program all seven days (M, TU, W, TH, F, SA, SU
will show in display) at the same time. Then you can use the individual day
programming to fine tune your program for the few set point times or temperatures
that you may wish to change.
Individual Days - allows you to program each day of the week individually to give
you the greatest schedule flexibility. Often used to fine tune programming after
initial programming. (continued on page 9)
cont.
Setting Your Energy Saving Program
5
9
Entering Your Program – 7 Day Mode (continued from page 8)
IMPORTANT NOTE! When in Whole Week programming, the thermostat will
check if all of the days of that group have the same program set point times and
temperatures. If so, the set point time and temperature of the individual set point
will be displayed. Otherwise, the individual set point time and temperature will be
blanked. The user is allowed to change the daily programs for this set point time
and temperature by pressing the or button. This will reset all the daily
programs of the group for that specific individual set point time and temperature
to the startup default for that set point. Continued pressing of the or button
by the user will change set point time and temperature settings as desired.
1. Place the system switch in the HEAT mode
of operation.
2. Press the PROG button to enter Program
setting mode. The
MORN set point of the
Whole Week Program Group will be
displayed. The display will show
M, TU, W,
TH, F, SA, SU, indicating the whole week is
being programmed. The hour and the
AM/PM indicator will be flashing.
3. If you wish to program each day individually press the DAY/TIME button to
select a specific day.
4. Press the or button to change the time to the desired hour in one hour
increments. Press the PROG button. The minute portion of the set point time
will begin flashing.
5. Press the or button to change the time to the desired minute in 10-minute
increments. Press the
PROG button. The SET temperature will begin flashing.
6. Press the or button to change the set point temperature to the desired
setting in 1º (.05˚ C) increments. Press the
PROG button. The thermostat will
now display the DAY set point time and temperature. Again, you will see the
hour and the AM/PM indicator flashing.
7. Follow steps 4 through 6 to set the set point times and temperatures for the
periods of
DAY, EVE, and NIGHT.
8. Place the system switch in the COOL mode of operation. The display will show
COOL. Follow steps 2 through 7 to program the set point times and
temperatures for the COOL mode.
NOTE: To erase all entered programs, current time of day, day of week and other
user settings, gently press the RESET button using a paper clip or a small pencil
tip. This will return all thermostat settings to their default values.
cont.
Setting Your Energy Saving Program
5