Braeburn 3300 - Manual (Page 7)

12
6
Additional Operation Features
Changing Set Temperature
1. Press and hold or button for
more than 1 second. The entire
display will flash once and the
SET indicator will be flashing.
Release the or button and
press the or button again
to adjust the set temperature.
2. The display will return to normal operating mode after 15 seconds, or you
can press the
BACK button to return to normal operating mode.
NOTE: Select either COOL or HEAT with the system button to view or change
cooling or heating set points.
Fan Cycle Fan Off Time Fan Run Time
Setting (minutes) (minutes)
24 24 12
40 40 12
60 60 12
120 120 12
5
Programming User Settings
cont.
Setting the Recirculating Fan Cycle
11
5
Programming User Settings
cont.
Setting the Humidifier Pad Monitor (see description on page 13)
The default setting is 0 days (monitor disabled).
12. Press and hold the NEXT
button for four seconds.
Press
NEXT button repeatedly
until “ SET XXX HUMID” is
displayed where “ XXX” is the
Humidifier Pad Monitor interval.
13. Press the or button to change the Humidifier Pad Monitor Interval to the
desired value of 0 (disabled), 180 or 365 days.
Keypad Lockout
This thermostat is equipped with a Multi-Level Keypad Lockout feature which
can be used to prevent undesired adjustment of the set point and/or programs.
Lock security level 1 locks all the buttons (including the reset button) except for
the , and backlight buttons. Lock security level 2 (default) locks the entire
keypad except for the backlight button [see Installer Option 13 in Section 4 for
information on setting lock security levels].
Setting Your Lock Code
Press and hold the
NEXT button for 4 seconds to enter into the User Settings
Mode. Press the NEXT button repeatedly until LOCK, SET and 3 digits are
displayed. Use the or buttons to adjust the first digit, press the NEXT button
to move to the second digit and repeat the process until you have entered all
3 digits. Once complete, you can press the
BACK and NEXT buttons together
or wait 30 seconds for the thermostat to return back to the main screen. The
thermostat is now ready to be locked with the 3 digit code you have created.
Locking the Thermostat
Press and hold the and buttons
together for five seconds. While
you are holding these buttons the
LOCK icon will flash once per
second and after 5 seconds the
LOCK icon and three digits will
appear in the display. Use the or buttons to enter the lock code you
previously created (see “Setting Your Lock Code”). After entering the first digit,
press the
NEXT button to move to the second digit and repeat this process
until you have entered all 3 digits. Once you complete entry of the third digit,
the thermostat will be locked and will automatically return to the main screen
and display the
LOCK icon. If you enter an incorrect three digit lock code, “no”
will appear in the display and you will have to repeat the process.
Unlocking the Thermostat
To unlock the thermostat, perform the exact same steps that you took to lock
it. Once your 3 digit lock code is successfully entered, the thermostat will be
unlocked and
LOCK will no longer appear in the display. If you enter an incor-
rect three digit lock code, “no” will appear in the display and you will have to
repeat the process.
SYSTEM FAN SET
HUMID SRVC
Recirculating Fan Mode
The Recirculating Fan Mode provides more even temperature distribution and
improves indoor air quality by circulating air through the furnace filtration
system more often. The Recirculating Fan Mode can be selected by changing
the fan option to recirculate (
CIRC) by pressing the FAN button. If no call for
heating or cooling occurs within the fan off cycle (see page 8), the fan will run
for 12 minutes. The highest setting, 120 minutes, will run the fan once every
2 hours. The lowest setting, 24 minutes (factory default), will run the fan every
24 minutes. During any call for heating or cooling, fan control operates in the
AUTO mode. This feature is available in the HEAT, OFF, COOL or EMER mode.
Setting the Recirculating Fan Cycle
1. Press and hold the NEXT button
for four seconds. Press
NEXT
button repeatedly until “ SET
XXX OC” is displayed where
“
XXX” is the Recirculating Fan
off cycle.
2. Press the or button to change the Recirculating Fan off cycle to the
desired value of 120, 60, 40 or 24 minutes.
3. Press the NEXT button again to return to the normal mode, or wait
30 seconds for the thermostat to return automatically.