Kenmore HE3 110 - Manual (Page 11)

WASHER USE
AWARNING
Fire Hazard
Me¥er place items in the washer that are
dampened with gasoline or other flammable
fluids.
No washer can completely remove oil.
Do not dry anything that has ever had any type of
oil on it (including cooking oils).
Doing so can result in death, explosion, or fire.
WARNING: To reduce the risk of fire, elecfric shock, or injury to
persons, read the IMPORTANT SAFETY INSTRUCTIONS before
operating this appliance.
The following is a guide to using your washer. Please refer to
other sections of this manual for more detailed Information.
Do not store laundry products on the top surface of this washer.
Vibration is normal during operation.
First Wash Cycle Without Laundry
Before washing clothes for the first time, choose NORMAL/
CASUAL cycle and run it without clothes. After installation, if a
complete cycle has not been run without clothes, use y
2 the
normal recommended amount of powdered or liquid High
Efficiency (HE) detergent or Vi the normal recommended amount
of regular powdered or liquid detergent. This initial cycle serves
to ensure the interior is clean before washing clothes.
1. To load the washer
Open the washer door by pulling on the handle. Sort laundry
according to color and type of fabric. Place a load of sorted
clothes in the washer. Do not overload washer. Overloading
can cause poor cleaning.
■ The washer can be fully loaded, but not tightly packed.
Washer door should close easily.
■ Mix large and small items. Avoid washing a single item.
Load evenly.
rubber rim at the front of the tub for small items.
2. Olose the washer door by pushing it firmly until the lock
clicks. The washer door will remain locked during the wash
cycle.
NOTE: After any wash cycle Is completed, the door must be
opened and then closed before a new cycle can begin. The
door can be opened only if PAUSE/CANCEL is selected while
the ADD A GARMENT light is glowing or if the cycle has been
canceled. See “To Cancel a Cycle.”
3. Open the Dispenser Drawer and add laundry products to the
detergent, bleach, or fabric softener compartments. Close
drawer slowly to avoid spills. See “Using the Dispenser.”
NOTE: For best performance, use High Etfficiency detergents.
The package for this type of detergent will be marked “HE” or
“High Efficiency.” The HE'’ “wash action” along with less water
could create too much sudsing with a regular detergent.
4. Turn on the washer by selecting one of the WASH CYCLES.
The indicator light for the selected cycle will glow. When
selecting a Wash Cycle, the preset options, Water Temp, Spin
Speed, and soil level for the selected cycle will glow. The
display shows the estimated time remaining. The preset
settings provide the recommended fabric care for the
selected cycle. See “Cycles.”
5. Select the desired OPTIONS. Not all Options are available
with all cycles. See “Options.”
6 . Select the desired MODIFIERS. Not all Modifiers are available
with all Cycles and Options. See “Modifiers.”
7. If desired, select the END OF CYCLE SIGNAL. The signal Is
helpful when you are washing items that should be removed
from the washer as soon as it stops. Select HIGH or LOW.
8. To begin the wash cycle immediately
Select and hold START (for approximately 1 second).
■ If you do not select START within 5 minutes of choosing a
cycle, the washer automatically shuts off.
■ When the wash cycle is complete, the CLOTHES CLEAN
status light glows, the door unlocks, and the wash load
can be removed from the washer. The washer powers
down automatically 5 minutes after the cycle is complete
and the CLOTHES CLEAN light goes off. To power down
the washer manually after the wash cycle is complete,
select PAUSE/CANCEL once.
9. To begin the wash cycle later
Select DELAY until the desired delay time (in hours) shows in
the Estimated Time Remaining display. Select START. The
countdown to the wash cycle will show in the display window.
11