Kenmore ULTRA WASH 665.1602 - Manual (Page 14)

Quick Rinse
Use this rinse cycle for rinsing dishes, glasses, and silverware
that will not be washed right away.
Do not use detergent with this cycle.
Wash Main
Wash
Rinse
or
Purge
Final
Rinse
Dry Time
(min) Water
Usage
(gal/L)
•
Rinse
10 1.8-2.2/
6.8-8.3
*lf the incoming water temperature is less than the
recommended temperature or food soils are heavy, the cycle will
automatically compensate by adding time, heat and water as
needed.
1. Press CANCEL/DRAIN. The Cancel/Drain light glows.
2. The dishwasher starts a 2-minute drain (if needed). Let the
dishwasher drain completely. The light turns off after
2 minutes. The door must be closed for the dishwasher to
drain.
To stop the drain
You can press CANCEL7DRAIN again to stop the drain.
Remember to drain the dishwasher before starting a new cycle.
To clear the indicators
Press CANCEL/DRAIN before starting the dishwasher to clear all
options and cycles.
You can add an Item anytime before the main wash starts. Open
the door and check the detergent dispenser. If the cover is still
closed, you can add items.
To add items
1. Carefully open the door slightly to stop the cycle. Wait for the
spraying action to stop before opening the door. The Start/
Resume light will flash.
2. Open the door. If the detergent dispenser cover is still closed,
add the item.
3. Close the door firmly until it latches.
4. Press START/RESUME.
IMPORTANT: If Lock On is selected, turn off the lock {see Lock
On section in “Option Selections”), or the Start/Resume light will
continue to flash.
You can customize your cycles by pressing an option. If you
change your mind, press the option again to turn the option off,
or select a different option if desired.
You can change an option anytime before the selected option
begins. For example, you can press an unheated drying option
anytime before drying begins.
Press START/RESUME to use the same cycle and option(s) as
the previous wash cycle.
NOTE: If the last cycle you completed was a rinse cycle, when
you press START/RESUME, the dishwasher runs the last full
wash cycle and options.
During the first minute of a cycle
1. Select a new cycle and/or options.
2. Check the detergent dispensers. They must be filled properly
for the new cycle.
3. The Start/Resume light will flash when the door is opened.
Make sure the door is closed.
4. Press START/RESUME.
After the first minute of a cycle
1 .
3.
4.
5.
Press CANCEL/DRAIN. The Cancel/Drain light glows. Your
dishwasher starts a 2-minute drain (if needed). Let the
dishwasher drain completely.
Check the detergent dispensers. They must be filled properly
for the new cycle.
Make sure the door is closed.
Select a new cycle and/or options.
Press START/RESUME.
Hi Temp Wash
Select this option to increase the water temperature during the
wash portions of the cycle. Hi Temp Wash raises the water
temperature to 145°F (63°C), in the main wash. Heating the water
helps improve washing results. Hi Temp Wash is useful when
loads contain tough food soil.
This option may add heat and wash time to the cycle.
NOTE: Hi Temp Wash is an option with the SMART WASH™,
Pots Pans, and Normal Wash cycles.
Sani Rinse
Select this option to raise the water temperature in the final rinse
to approximately 155°F (
6 8 °C). Sani Rinse adds heat and time to
the cycle. This high temperature rinse sanitizes your dishes and
glassware in acoordance with NSF/ANSI Standard 184 for
Residential Dishwashers. Certified residential dishwashers are
not intended for licensed food establishments.
NOTE: Sani Rinse is an option with SMART WASH"^'^, Pots Pans,
and Normal Wash cycles. Only these sanitization cycles have
been designed to meet the NSF/ANSI requirements.
14