Campbell Hausfeld JB004250 - Manual (Page 2)

● Always
disconnect the
tool from the
power source
when
unattended,
performing any maintenance or
repair, clearing a jam, or moving the
tool to a new location. Always
reconnect the air line BEFORE
loading any fasteners. Do not load
the tool with fasteners when either
the trigger is depressed or the Work
Contact Element (WCE) is engaged.
The tool could eject a fastener
causing death or serious personal
injury.
● Always fit tool
with a fitting
or hose
coupling on or
near the tool in
such a manner
that all compressed air in the tool is
discharged at the time the fitting or
hose coupling is disconnected. Do
not use a check valve or any other
fitting which allows air to remain in
the tool. Death or serious personal
injury could occur.
● Never place hands or
any other body parts
in the fastener
discharge area of the
tool. The tool might
eject a fastener and
could result in death or serious
personal injury.
● Never use gasoline
or other flammable
liquids to clean the
tool. Never use the
tool in the presence
of flammable liquids or gases.
Vapors could ignite by a spark and
cause an explosion which will result
in death or serious personal injury.
● Always remain in
a firmly balanced
position when
using or handling
the tool.
● Do not remove,
tamper with, or
otherwise cause
the Work Contact
Element (WCE) or
trigger to become
inoperable. Do not operate any tool
which has been modified in a like
fashion. Death or serious personal
injury could result.
● Do not touch the
trigger unless
driving fasteners.
Never attach air
line to tool or
carry tool while
touching the
trigger. The tool could eject a
fastener which will result in death
or serious personal injury.
Warning
indicates
a potentially hazardous situation
which, if not avoided, COULD result in
death or serious injury.
General Safety
Information
(Continued)
● Ensuring that tools which require
repair are not further used before
repair. Tags and physical
segregation are recommended
means of control.
Danger
indicates
an imminently hazardous situation
which, if not avoided, WILL result in
death or serious injury.
● Read and understand
tool labels and manual.
Failure to follow
warnings, dangers, and
cautions could result in
DEATH or SERIOUS
INJURY.
● Do not use any type
of reactive gases,
including, but not
limited to, oxygen
and combustible
gases, as a power
source. Use filtered, lubricated,
regulated compressed air only. Use
of a reactive gas instead of
compressed air may cause the tool
to explode which will cause death or
serious personal injury.
● Use only a pressure-
regulated
compressed air
source to limit the air
pressure supplied to
the tool. The
regulated pressure must not exceed
100 psi. If the regulator fails, the
pressure delivered to the tool must
not exceed 200 psi. The tool could
explode which will cause death or
serious personal injury.
2
Magazine
Trigger
Nailer Components And Specifications
Model JB004250 Operating Instructions
• REQUIRES: 0.4 SCFM with 10
nails per minute @ 90 psi
• AIR INLET: 1/4 inch NPT
• NAIL SIZE RANGE: 3/8 inch to 2
inch
• MAGAZINE CAPACITY:
100 Nails per load, 18 gauge
• WEIGHT: 3 lbs., 7 oz.
• LENGTH: 10
1 ⁄ 8 inch
• HEIGHT: 9 1 ⁄ 2 inch
• MAXIMUM PRESSURE: 100 psi
• PRESSURE RANGE: 60-100 psi
Nail Discharge Area
Nail Loading Area
Adjustable
Exhaust
Work Contact
Element (WCE)
Reload Indicator
CAMPBELL CAMPBELL PROFESSIONAL PROFESSIONAL HAUSFELD HAUSFELD
100 psi
MAX.
Quick Clear
Nose
Adjustable
Depth
Control
Magazine
Latch
Button
O
CO
2
www.chpower.com