Kenwood KDC-MP408U - Manual (Page 12)

Menu Operation
Menu System
tup the following functions;
Display Setting Source
"SECURITY
SET"/
"SECURITY
CLR" Referto
page 12 Sets/Resets security code EÌ1
"CLOCK
ADJUST" Referto
page 13 Sets the clock. JMzé
"DISPLAY" 0N*/0FF Turns offthe display when no
operation is performed.
—
"DIMMER"
*1,2,3
AUT0*/0FF Dims the display in conjunction
with the light switch of the
vehicle.
"DIMMER"« ON/OFF* Adjusts the brightness of
the display according to the
surrounding illumination.
"DOT LINE" 0N*/0FE Specifies whether to display the
red dotted line on the display.
"SWPRE"«''REAR*/
SUB-W
Sets the preout output.
"AMP"«' 0N*/0FF Turns on/offthe built-in amplifier.
"AMS
CONTROL"*' Referto
page 13 Controls the connected LX
amplifier. —
"Z0NE2"*'''’REAR*/
FRONT
Specifies the destination of AUX
input sound when the Dual Zone
function is turned on. fSB~l
"SUPREME" 0N*/0FF Turns ON/OFF the Supreme
function.
"CRSC" OFF/ON* Switches to Monaural to decrease ■aji»
noise when reception is poor.
"NAME SET"Referto
page 14
Sets the display when switched
to AUX source.
"SCROLL" AUTO*/
MANUAL
Specifies whether the text is
scrolled automatically. —
"RECEIVE
MODE" Referto
page 14 Sets the receive mode of HR radio, iiiwii
"ESN" — Displays the Electronic Serial
Number of satellite radio.
"AUX" OFF/ON r/ Sets whether to display AUX
0N2 during source selection.
EH
"CD READ" r/2 Sets the CD read mode. mm
"DEMO
MODE" Refer to
page 14 Specifies whether to enable
demonstration. —
*Factory setting
Function of KDC-X492.
*2 Function of KDC-MP438U.
•3 Function of KDC-MP408U.
*'• Function of KDC-MP338.
Displayed item is depending on currently selected
source. The mark in Source column shows the
12
I KDC-X492/KDC-MP438U/KDC-MP408U/KDC-1
source to which the item is displayed.
[ SB I : Can be set in other than standby state.
m:\zm : Can be set in standby state.
MM : Can be set while Audio file source of CD/USB
(excluding iPod).
áldk^it : Can be set during FM reception.
: Can be set during Satellite radio source.
yimii : Can be set while accessing AUX source.
iSIrisI : Can be set while HD Radio source.
— : Can be set during all sources.
1 Enter Menu mode
Press the [M JOG] button for at least 1 second.
"MENU" is displayed.
2 Select the menu item
Push the Control knob towards up or down.
3 Set the menu item
Push the Control knob towards right or left.
4 Exit Menu mode
Press the [MJOG] button.
Refer to the respective page for information on how to
set the items with reference page number.
"ZONE2"is displayed when "2ZONE"in <Audio Setup>
(page 7) is set to "ON.
Refer to the <Appendix> (page 16) for the details of the
menu items.
Strong electrical fields (such as from power lines) may
cause unstable sound quality when CRSC is turned ON.
In such a situation, turn it OFF.
Activating Security Code
• You can set the Security Code with a 4 digit number of your
choice.
• The Security Code cannot be displayed or referenced. Make
a note of the Security Code and treasure it up.
1 Select Security Code item during Menu mode
Select the "SECURITY SET" display.
For how to select menu items, refer to <Menu
System>(page 12).
2 Enter Security Code mode
Press the Control knob for at least 1 second.
When "ENTER" is displayed, "CODE" is also displayed.
3 Select the digits to enter
Push the Controi knob towards right or left.
4 Select the Security Code numbers
Push the Control knob towards up or down.
MP338