Kenwood KRF-V5560D - Manual (Page 18)

Preparing for surround sound
[
• For VR-615 (НТВ model), do not select "LRG" (large) for surround
speaker as this will cause the speaker to malfunction.
If you have selected other than "LRG" as the center speaker
setting,
(D SURR ON : Surround speaker setting mode to the receiver is
ON,
(D SURR OFF ; Surround speaker setting mode to the receiver is
OFF.
0 Press the SET UP key again to accept the setting.
• The subwoofer re-mix setting indication "SW RE-MIX" scrolls
across the display.
"SW RE-MIX" scrolls across the display.
ШОШ
/8WÌ
a □ ...
• If subwoofer is turned OFF, subwoofer re-mix setting is not
visible,
0 Use the MULTi CONTROL knob or keys to select the
appropriate subwoofer remix setting.
RMX OFF : Subwoofer re-mix set mode to the receiver is OFF,
0 Press the SET UP key to accept the setting.
• The receiver enters the speaker volume level adjustment
mode.
• In step El and S, Indications appear only for the selected
channels of the speakers that require adjusting.
Q Adjust the speaker volume level.
From your usual listening position, adjust the volume levels. The
volume levels from each speaker should be the same.
O Press the SET UP key to begin TEST TONE.
r- © AUTO
L. ® MANUAL
0 The selection of AUTO/MANUAL TEST TONE is done by the
MULTi CONTROL knob or keys.
Press the SET UP key again to seiect either AUTO or MANUAL.
Use the MULTi CONTROL knob or keys to adjust the voiume
lev.ei of the test tone output from the speaker channel to be
adjusted.
For AUTO selection, the test tone is heard from the speakers
in the foiiowing sequence for 2 seconds each:
I - > L — C -» R — SR — SL — SW ------------ 1
The channel indication blinks while the test tone Is being ouput.
i....
• If you change the volume level settings for the speakers while
listening to music, the settings referred to on this page are also
changed.
-(2B
• If the speaker setting selects are OFF, the speaker level settings
are reset. -
S Input the distance to the speakers.
O Select the DISTANCE from the set up displays and press the
SET UP key again.
0 Measure the distance from the listening position to each of
the speakers.
Jot down the distance to each of the speakers.
Distance to front speakers
Distance to center speaker
Distance to surround speakers , feet (meters)
_ feet (meters)
. feet (meters)
O Use the MULTI CONTROL knob or keys to select the distance
to the front speakers.
The speaker indicator to be adjusted blinks,
^ \ I / ^__________________________________________
Ш ПК;
"/ I X""
Indication in feet Indication in meters
•The allowable setting range is 1 to 30 feet (0.3m to 9.0m),
adjustable in 1 foot (0.3m) increments.
O Press the SET UP key to accept the settings.
© Repeat steps © and © to input the distance for each of the
speakers.
© Setup is complete when the input indication appears.
ШОШ :....
IMi :••••
О □ i.............
•The speakers you have selected should appear on the display.
Confirm that all the speakers have been correctly selected.
0 Press the SET UP key to exit the SET UP mode.
Input level adjustment (analog sources only)
If the input level of an analog source signal is too high, the CLIP indicator
will blink to indicate the source signal. Adjust the input level.
O Use the INPUT SELECTOR knob to select the source of which the
input level you want to adjust.
•You can store a separate input level for each input source.
0 Press the SOUND key repeatedly until the "INPUT" indication
appears.
O Use the MULTI CONTROL knob or keys to adjust the input level.
SI"« шаш T ¡\ • •.. • i • г
iswi : : : ■ '
О □ ,i. ; ; ;..
• The adjustment mode is displayed for approximately eight sec­
onds.
• The input level may be adjusted to any one of three settings: OdB,
-3dB, and -6dB. (The initial setting is OdB.)
G Press the SET UP key.
• The test tone is turned off. The receiver enters the mode for
inputting the distance to the speakers.
O Press the SOUND key again to return to the input indication.
O For MANUAL selection, press the SET UP key each time to
select the speaker channel.
18
'