Futaba 8FG 2.4GHz - Manual (Page 109)

109 )XQFWLRQVRI0RGHO0HQX +HOLFRSWHU)XQFWLRQV !
ŏ6HOHFW WKH IXQFWLRQ QDPH
and return to the Model
menu by touching the
RTN button.
<SensorTouch™>
3,7&859(3,775,0
3LWFK&XUYH
7KLVIXQFWLRQDGMXVWVWKHSLWFKRSHUDWLRQFXUYH
for each flight condition to optmize the model's
performance in relationship to the throttle stick
position.
*A simple curve can be created by reducing the number of
LQSXWSRLQWVWRWZRRUWKUHHDQGWKHQHQWHULQJWKHVSHFL¿HG
value at the corresponding points.
1RUPDOFXUYHDGMXVWPHQW
)RU QRUPDO FXUYH FUHDWH D EDVLF SLWFK FXUYH FHQWHUHG
DERXWKRYHULQJ8VHWKLVIXQFWLRQWRJHWKHUZLWKWKH7+5
&XUYH 1RUPDO IXQFWLRQDQGDGMXVWWKHFXUYHVRWKDWXS
GRZQFRQWUROLVEHVWDWDFRQVWDQWHQJLQHVSHHG
,GOHXSFXUYHDGMXVWPHQW
)RU WKH KLJK VLGH SLWFK FXUYH VHW WKH PD[LPXP SLWFK
VRWKDWLWGRHVQRWRYHUORDGWKHHQJLQH)RUWKHORZVLGH
SLWFKFXUYHFUHDWHFXUYHVPDWFKHGWRORRSUROO'DQG
other purposes and use the idle up curves according to the
performance.
7KURWWOHKROGFXUYHDGMXVWPHQW
7KH WKURWWOH KROG FXUYH LV XVHG ZKHQ H[HFXWLQJ DXWR
rotations.
2SHUDWLRQSUHFDXWLRQV
:DUQLQJ
:KHQDFWXDOO\VWDUWLQJWKHHQJLQHDQGIO\LQJ
DOZD\VVHWWKHLGOHXSFRQGLWLRQVZLWFKWR2))
and start the engine at idle.
ŏ 6HOHFW >3,7 &859(@ DW WKH 0RGHO PHQX
and access the setup screen shown
below by touching the RTN button.
ŏ 3LWFK FXUYH FRS\
Scrolling
ŏ0RYLQJ FXUVRU
ŏ6HOHFWLQJ PRGH
ŏ$GMXVWLQJ YDOXH
ŏ7R QH[W SDJH
&XUUHQWO\VHOHFWHGFRQGLWLRQQDPH
Ɣ3LWFKFXUYHFRS\IXQFWLRQ
Move the cursor to COPY and touch the RTN
button to switch to the data input mode.
Select the copy destination condition by
scrolling the touch sensor and touch the RTN
button. Select the [YES] and touch the RTN
button.
ŏ FXUYH UDWH
ŏ FXUYH SRLQW
6HWWLQJPHWKRG
ƔSRLQWFXUYHVHWWLQJ
[Curve rate setting]
1. Move the cursor to the curve rate setting
item you want to adjust and touch the RTN
button to switch to the data input mode.
Adjust the rate by scrolling the touch sensor.
,QLWLDO YDOXH 3  3  3  3
 3 
$GMXVWPHQW UDQJH a
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
reset to the initial value.
Touch the RTN button to end the adjustment
and return to the cursor mode.
2. Repeat this procedure for each point as
desired.
[Moving curve point]
1. Move the cursor to the curve point setting
item you want to adjust and touch the RTN
button to switch to the data input mode.
Adjust the curve point by scrolling the touch
sensor.
,QLWLDO YDOXH 3   3  3  3
 3 
$GMXVWPHQW UDQJH 8S WR  LQ IURQW RI WKH
adjoining point
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHFXUYH
SRVLWLRQLVUHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to end the adjustment
and return to the cursor mode.
2. Repeat this procedure for each point as
desired.
[Deleting/returning curve point]
1. Move the cursor to the curve point setting
item you want to delete/return and touch
the RTN button for one second.
*The graph display includes the pitch
trim operation.