Futaba R2004GF - Manual

R2004GF
FHSS-2.4GHz system,
4-channel receiver
Compliance Information Statement (for U.S.A.)
This device, trade name Futaba Corporation of America, model number R2004GF, complies
with part15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesiredoperation.
The responsible party of this device compliance is:
Futaba Service Center
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.
TEL (217)398-8970 or E-mail: [email protected] (Support)
Thank you for purchasing the R2004GF
receiver. This receiver is designed for use
with the Futaba FHSS system transmitter.
Please pay special attention to the
information contained within this manual
and transmitter's manual in order to have
a pleasant running/flying experience. The
R2004GF is compatible with the FHSS
system transmitters as shown "Transmitter
and Receiver Compatibility".
FUTABA CORPORATION
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan
Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
1M23N17436 ©FUTABA CORPORATION 2010, 8 (1)
R2004GF Specifications:
( FHSS system, 4-channel receiver)
• Receiving on 2.4GHz band
• Power requirement: 4.8V or 6V
(shared with servo)
• Current drain: 30mA (at no signal)
• Size: 1.54x1.02x0.39” (39x26x10mm)
• Weight: 0.28oz. (8g)
 WARNING
 NEVER use dry batteries for the
power supply of the R2004GF as
they may cause difficulties.
Link Procedure
Each transmitter has an individually
assigned, unique ID code. In order to start
operation, the receiver must be linked
with the ID code of the transmitter with
which it is being paired. Once the link is
made, the ID code is stored in the receiver
and no further linking is necessary unless
the receiver is to be used with another
transmitter.
1
Place the transmitter and the receiver
close to each other within one (1)
meter
2
Turn on the transmitter and the
receiver.
3
Push and hold the Link switch on the
receiver.
4
When the link is complete, the LED
on the receiver changes to solid
green.
* Please refer to the table below for LED
status and receiver condition.
No signal reception Red : On
Receiving signals Green: On
Receiving signals, but ID
is unmatched.
Green: Blink
* If there are many FHSS systems turned
on around your receiver, it might not link
to your transmitter. In this case, even
if the receiver’s LED stays solid green,
unfortunately the receiver might have
established a link to one of the other
transmitters. This is very dangerous
if you do not notice this situation. In
order to avoid the problem, we strongly
recommend you to double-check whether
your receiver is controlled by your
transmitter by giving throttle input, etc.
and then checking servo response.
 WARNING
 After the linking is done, please
cycle receiver power and check if
the receiver to be linked is really
under the control by the transmitter
to be linked.
 D o n o t p e r fo r m t h e l i n k i n g
procedure with motor's main wire
connected or with the engine
operating as it may result in serious
injury.
FHSS-2.4GHz/S-FHSS-2.4GHz System
Transmitter and Receiver Compatibility
Transmitter
FHSS
Receiver
S-FHSS/FHSS
Receiver
R603GF
R2004GF
R2104GF
T2PL-2.4G (FHSS) Okay Okay F/S function: Ch2
T3PL-2.4G (FHSS) Okay Okay F/S function: Ch2
T4YF-2.4G (FHSS) Okay Okay
T4PL-2.4G
S-FHSS
High Speed
— Okay
F/S function: All channels
B-F/S function: Ch2
*Digital servo only at High Speed
mode
Normal
FHSS Okay Okay F/S function: Ch2
NOTE: Futaba FHSS/S-FHSS system and FASST system are
not compatible each other.
Link switch LED
Ch output (1 to 4)
Battery terminal (B)