Futaba R2008SB - Manual

Applicable systems: Futaba S-FHSS/FHSS-2.4GHz system and TM-FH RF Module
R2008SB
S-FHSS/FHSS-2.4GHz System
S.BUS Port and 8 Channels for Conventional System
Receiver
Compliance Information Statement
(for U.S.A.)
This device, trade name Futaba Corporation of America, model
number R2008SB, complies with part15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
The responsible party of this device compliance is:
Futaba Service Center
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.
TEL (217)398-8970 or E-mail: [email protected] (Support)
R2008SB Specifications
S-FHSS/FHSS-2.4GHz system/S.BUS port and 8 channels for
conventional system receiver
• Dual antenna diversity
• Size: 0.98 x 1.69 x 0.55 in. (24.9 x 42.8 x 14.0 mm)
• Weight: 0.34 oz. (9.5g)
• Power requirement: 4.8V to 7.4V
• Battery F/S Voltage: 3.8V
* Be sure that when using ESC's regulated output the current capacity of the
ESC must meet your usage condition.
* The Battery F/S voltage is set for 4-cell NiCd/NiMH battery. Battery F/S
function doesn't work properly when other type battery is used.
* The fail safe function can be set for each channel , however it differs ac-
cording to the transmitter. When you use TM-FH RF Module , the fail safe
function can be set for 3-channel only.
* S.BUS port: R2008SB can be used up to 8 channels, however, it differs ac-
cording to the transmitter. An unused channel is a neutral signal. The F/S
setting channel at F/S is F/S position. Another, it is Hold signal.
Thank you for purchasing a Futaba R2008SB S-FHSS/FHSS-2.4GHz compatible receiver.
The R2008SB has an S.BUS system output port and a conventional system channel outputs. It can also be used with
conventional system servos, etc. in addition to S.BUS system compatible servos and gyros, etc.
 The antenna should not be pulled.
 Keep the antenna away from the motor, ESC
and other noise sources as you can.
 Be sure that the two antennas are placed at 90
degrees to each other.
• The R2008SB has two antennas. In order to maximize
signal reception and promote safe modeling Futaba has
adopted a diversity antenna system. This allows the
receiver to obtain RF signals on both antennas and fly
problem-free.
Antenna installation for carbon fuse
 WARNING
 The antenna portion of 30mm tip must be fully
exposed.
• Please make sure that the exposed portion won't be slided
back in the fuse by the wind pressure or other force during
the flight session.
Usage precaution
• Futaba S-FHSS/FHSS system does not work with cur-
rent Futaba FASST system. Futaba FASST system and
S-FHSS/FHSS system are not compatible each other.
 WARNING
 Wrap the receiver with something soft, such as
foam rubber, to avoid vibration. Moreover, The
receiver must not get wet.
 Keep away from conductive material to avoid the
short circuit.
Antenna installation precaution
 Do not cut or bundle the receiver antenna wire.
 Do not bend the coaxial cable . It causes dam-
age.
(Antenna installation)
90˚
Link switch
Antenna
LED
R2008SB
for conventional
system
Channel
Channel
Channel 8 output
for conventional
system
/Battery terminal
output
output
S.BUS Port
(Connectors)
1M23N17452