Futaba R6106HF / HFC - Manual

Usage condition on "High
Speed mode"
 CAUTION
 The "High Speed mode" accept
the digital servos only or most
type of peripherals.
• If any analog servos connected to these
output as it will cause malfunction.
Please check the peripherals if there's
any malfunction with whole stick lever
throw. If any malfunction occur please
change the operation mode to "Normal
mode."
R6106HF
For parkflight or indoor use airplanes.
For electric helicopters up to 1000mm of main rotor diameter.
R6106HFC
For small size airplanes such as wing span of up to around 1300mm.
For carbon fuse such as non powered sail planes.
Compliance Information Statement
(for U.S.A.)
This device, trade name Futaba Corporation of
America, model number R6106HF/R6106HFC,
complies with part15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference
received, including interference that may cause
undesiredoperation.
The responsible party of this device compliance is:
Futaba Service Center
3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.
TEL (217)398-8970 or E-mail: [email protected] (Support)
TEL (217)398-0007 or E-mail: [email protected] (Service)
R6106HF/R6106HFC Specifications
FASST-2.4GHz system 6-channel receiver
• Power requirement: 4.8V~7.4V (Voltage range:
3.5~8.5) regulated output from ESC, etc. (*1)
• Battery F/S voltage: 3.8V
• Size: 0.85 x 1.53 x 0.48 in. (21.7 x 38.8 x 12.3 mm)
• Weight: 0.24 oz. (6.7g)/0.25 oz. (7.1g)
(*1) Be sure that when using ESC's regulated output
the capacity of the ESC must meet your usage
condition.
Re-adjust the F/S position (only
for TM-7/TM-8)
1
Press and hold the Link/Mode switch
between one(1) and two(2) seconds.
0 to 1 sec. 1 to 2 sec. More than 2 sec.
0 sec. 1 sec. 2 sec.
Press and Hold time
No function With TM-7, TM-8 To set the F/S
position(No re-link)
Re-link(ID set) and to
set the F/S position
No function With TM-10, TM-14,
6EX, 7C, etc.
Re-link(ID set)
FUTABA CORPORATION Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba 299-4395, Japan
©FUTABA CORPORATION 2011, 07 (2)
Operation Mode Select
The operation mode is on "Normal mode" from
factory shipping. When to change the mode,
please follow the steps shown below.
1
Turn off the receiver.
2
Press and hold the link/mode switch and
turn on the receiver. Keep the switch hold
more than one(1) second. The LED starts
flashing with the current status.
3
Release the switch.
4
Turn off the receiver.
By doing this step, the mode can switch over
between two(2) modes.
0 to 1 sec. More than 1 sec.
0 sec. 1 sec.
Press and Hold time
Turn on the receiver.
No function
Showing the CURRENT
mode with blink.
Red Blink = Normal
Green/Red Blink =
High Speed
Solid as the mode changed.
Red Solid = Normal
Green/Red Solid = High
Speed
(Become Red after one (1)
second)
（ Function） To change the mode between
Normal and High Speed
（ LED Status）
Please check the operation mode by observing
the LED when turning on the receiver. If possible
there's no FASST transmitter turned on around you
in order to make firmer check.
When turn on the receiver, the LED will be;
• Red when on "Normal mode"
• Green and Red (makes Orange) when on "High
Speed mode". (After two(2) seconds, change to Red.)
If there are some FASST transmitter turned on
around the receiver, the LED may show the above
status for a brief moment then changed to the
status indication as shown in the "LED indication"
table.
LED Indication
Green Red Status
Solid Solid Initializing
Off Solid No signal reception
Solid Off Receiving signals
Blink Off Receiving signals but ID is unmatched
Link to the transmitter
1
Press and hold the Link/Mode switch more
than two(2) seconds.
 WARNING
 Do not perform the linking procedure
with motor's main wire is connected or
the engine is operating as it may result in
serious injury.
 While the linking is done, please cycle
receiver power and check if the receiver
to be linked is really under the control by the
transmitter to be linked.
Thank you for purchasing the R6106HF,
R6106HFC FASST receiver. These models have
two(2) operation mode as shown below.
Normal mode/High Speed mode
The "Normal mode" accepts any type of servos
or the peripherals as the frame rate of the output
is 16ms. The "High Speed mode" only accept
the digital servos, including BLS series, and
most peripheral equipments such as the gyros or
brushless ESCs. The frame rate of the outputs is
8ms.
The R6106HF, R6106HFC are compatible with
the FASST transmitters as shown below.
T6EX-2.4GHz, T7C-2.4GHz, TM7,
T8FG-2.4GHz, TM8, T10CG-2.4GHz ,
TM10, TM14 (on 7ch-mode)
LED
Link/Mode Switch
R6106HF
R6106HFC
LED
Link/Mode Switch
Antenna
Antenna
Antenna installation for carbon fuse
(R6106HFC)
 WARNING
 The antenna portion of 30mm tip
must be fully exposed.
• Please make sure that the exposed portion won't
be slided back in the fuse by the wind pressure
or other force during the flight session.
Usage precautions about the power source
We do not recommend to use the power source of less
than 4.0V but if to use the lower voltage source please
keep in mind the condition shown below.
• Fail Safe function MUST be in "off" since the battery f/s will
disturb the normal operation.
• Please make sure that the full loaded condition of the ESC
and the servos won't disturb the receiver operation before
start flight.
This is very important since the receiver will stop operation
when the supply voltage drops to around 3.0V.
• Please be sure that the ESC or servos can keep flawless
operation till such a lower voltage.
If the servo's maximum voltage rating is less than 8.5V,
the power source voltage must not exceed the servo's
rating.
1M23N17447