Futaba R6203SB User Manual

R6203sb

Advertising
background image

Usage condition for conventional system

output (Ch1-3) on "High Speed mode"

 CAUTION



The "High Speed mode" accept the digital

servos only or most type of peripherals.

• If any analog servos connected to these output as it

will cause malfunction. Please check the peripherals if

there's any malfunction with whole stick lever throw. If any

malfunction occur please change the operation mode to

"Normal mode."

Applicable systems: FASST-2.4GHz 7ch or 8ch/10ch/Multi-ch system

R6203SB

FASST-2.4GHz (7ch/8ch/10ch/Multi-ch) System

S.BUS Port and 3 Channels for Conventional System

High-speed Receiver

Compliance Information Statement

(for U.S.A.)

This device, trade name Futaba Corporation of America, model

number R6203SB, complies with part15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including

interference that may cause undesiredoperation.

The responsible party of this device compliance is:

Futaba Service Center

3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.

TEL (217)398-8970 or E-mail: [email protected] (Support)

R6203SB Specifications

FASST-2.4GHz (7ch/8ch/10ch/Multi-ch) system/S.BUS port

and 3 channels for conventional system/high-speed receiver
• Dual antenna diversity

• Size: 0.89 x 1.47 x 0.37 in. (22.5 x 37.4 x 9.3 mm)

• Weight: 0.25 oz. (7.2g)

• Power requirement: 3.7V to 7.4V(Voltage range: 3.5 to 8.4V)

* Be sure that when using ESC's regulated output the capacity of the ESC

must meet your usage condition.

* The Battery F/S voltage is set for 4-cell NiCd/NiMH battery. Battery F/S

function doesn't work properly when other type battery is used.

* The fail safe function can be set for each channel when on "Multi-ch" mode,

however, it differs according to the transmitter. When on "7ch" mode, the

fail safe function can be set for 3-channel only.

*

S.BUS port: R6203SB can be used up to 7 channels or less on the "7ch"

mode and 16 channels + DG1/2 or less on the "8ch/10ch/Multi-ch" mode,

however, it differs according to the transmitter.

Thank you for purchasing a Futaba R6203SB FASST-2.4GHz

compatible receiver.
The R6203SB has an S.BUS system output port and a

conventional system channel outputs. It can also be used with

conventional system servos, etc. in addition to S.BUS system

compatible servos and gyros, etc.
When the linking procedure is performed, R6203SB

recognizes the signal mode (FASST-2.4GHz 7ch mode or

8ch/10ch/Multi-ch mode) automatically.
In addition, the operating mode (high-speed mode/normal

mode) can be selected.

Usage precautions about the power source

We do not recommend to use the power source of less than

4.0V but if to use the lower voltage source please keep in

mind the condition shown below.

• Fail Safe function MUST be in "off" since the battery f/s will

disturb the normal operation.

• Please make sure that the full loaded condition of the ESC

and the servos won't disturb the receiver operation before

start flight.

This is very important since the receiver will stop operation

when the supply voltage drops to less than 3.5V.

• Please be sure that the ESC or servos can keep flawless

operation till such a lower voltage.

The power source voltage must not exceed the servo's

rating.

Antenna installation precaution

 WARNING



Be sure that the two antennas are placed at 90

degrees to each other.

• Futaba's dual antenna diversity, or DAD, then seamlessly

selects the best signal reception between these antennas to

ensure that there is no loss of signal.

Antenna installation for carbon fuse

 WARNING



The antenna portion of 30mm tip must be fully

exposed.

• Please make sure that the exposed portion won't be slided

back in the fuse by the wind pressure or other force during

the flight session.

(Antenna installation)

90˚

Link/Mode switch

LED

R6203SB

• Channel 2 output for conventional

system (

2)

• Channel 1 output for conventional

system (

1)

• Channel 3 output for conventional

system (

3)/Battery terminal (B)

S.BUS Port (S.BUS)

(Connectors)

Advertising