Grove Gear 800 SERIES GROVE GEAR IRONMAN - Manual (Page 2)

800 Series - size 813 thru 832
11. The replacement input seal should now be installed. See the chart below for seal usage.
a. Grease the seal lips with bearing grease.
b. Apply a light coat of bearing grease to the shaft extension or quill coupling.
c. Slide the seal onto the shaft extension or quill coupling being careful not to fold the inner lip over on any shaft
steps.
d. Press the seal into its bore with a sleeve that presses on the seal casing, being careful to keep the seal
square in its bore. The face of the seal should be recessed below the housing surface approxximately 7/32”.
12. The output assembly should now be placed completely back in its original position in the gear housing. Note: Do not
force the output gear into its mesh with the input shaft. Doing so may damage the output gear teeth.
13. Apply a light coating of grease to the o-ring on the output cover. Apply a thread locking compound to the threaded
portion of the output cover fasteners. Reassemble the shims and output cover (and ou put flange, if applicable) to the
gear housing. For unit sizes 813 through 826, the output cover bolts should be tightened to 185 inch-pounds. For unit
sizes 830 through 832, the output cover bolts should be tightened to 330 inch-pounds.
14. If a motor flange was removed during disassembly of the input, it should now be reassembled to the gear housing.
Apply a thread locking compound to the threaded portion of the motor flange fasteners. The motor flange bolts should
be tightened to 185 inch-pounds.
15. Remove the electrician’s tape from all keyways and refill the unit with oil to the appropriate level.
800 SERIES GROVE GEAR IRONMAN SEAL USAGE
Upper line(s) list Grove Gear part # (Chicago Rawhide part #)
Lower line gives seal dimensions, expressed as: (shaft dia.) x (seal bore dia.) x (seal width)
All seals are double lip, style CRWA1, and Viton lip material
UNIT SINGLE SOLID DOUBLE INPUT QUILL INPUT SOLID HOLLOW
SIZE INPUT COVER END [Motor Size] OUTPUT OUTPUT
813 93207A (534948) 93150 (6383) [All]: 93216A (534953) 93217A (9939)
.625 x 47mm x 7mm .625 X 1.375 x .25 93212A (534951) .875 x 1.624 x .25 1.000 x 1.624 x .25
1.375 x 47mm x 7mm
815 93207A (534948) 93150 (6383) [All]: 93216A (534953) 93217A (9939)
.625 x 47mm x 7mm .625 X 1.375 x .25 93212A (534951) .875 x 1.624 x .25 1.000 x 1.624 x .25
1.375 x 47mm x 7mm
818 93207A (534948) 93150 (6383) [All]: 93217A (9939) 93174 (14259)
.625 x 47mm x 7mm .625 X 1.375 x .25 93212A (534951) 1.000 x 1.624 x .25 1.438 x 2.250 x .313
1.375 x 47mm x 7mm
821
93207A (534948) 93150 (6383) [All]: 93217A (9939) 93143 (19227)
.625 x 47mm x 7mm .625 X 1.375 x .25 93212A (534951) 1.000 x 1.624 x .25 1.938 x 2.623 x .313
1.375 x 47mm x 7mm
824
93208A (534956) 93180A (7624) [All]: 93218A (534955) 93143 (19227)
.750 x 52mm x 7mm .750 X 1.624 x .25 93214A (534958) 1.250 x 2.125 x .25 1.938 x 2.623 x .313
1.563 x 52mm x 7mm
826 93209A (534949) 93211A (9308) [All]: 93218A (534955) 93143 (19227)
.938 x 62mm x 8mm .938 X 1.624 x .25 93215A (534957) 1.250 x 2.125 x .25 1.938 x 2.623 x .313
1.875 x 62mm x 8mm
830 93335 93335 [All]: 93035 (14994) 93163
1.125 x 2.835 x .315 1.125 x 2.835 x .315 93340 1.500 x 2.374 x .313 2.75 x 3.5 x .375
1.875 x 2.835 x .315
832 93335 93335 [All]: 93035 (14994) 93163
1.125 x 2.835 x .315 1.125 x 2.835 x .315 93340 1.500 x 2.374 x .313 2.75 x 3.5 x .375
1.875 x 2.835 x .315
7050G - BH/SK - 7/11 - PDF