Interlogix VE1120 - Manual (Page 5)

P/N 146279999-2 (ML) • REV C • ISS 28JUN12 5 / 32
PIR Red LED Alarm relay To reset
Low voltage Open (Alarm) Apply correct voltage
PIR intruder
alarm Open (Alarm) Automatically after 3 s
PIR/AM Red
LED
Yellow
LED Alarm
relay AM
relay To reset
Start up Closed Closed Automatically
after 60 s
Low voltage Open
(Alarm) Open
(Alarm) Apply correct
voltage
PIR intruder
alarm Open
(Alarm) Automatically
after 3 s
Latched PIR
(Memory) Switch to Night
mode
AM alarm Open*
(Alarm) Open
(Alarm) See DIP
switch 3
After AM
reset Switch to Night
mode
Technical
fault Open
(Alarm)
Do a successful
walk test
Continuously on Normal blinking (1 Hz)
Fast blinking (4 Hz)
* Depends on the setting of the DIP switch SW4.
Specifications
VE1120 VE1120AM
Detector PIR PIR with AM
Signal processing V2E
Range 20 m
Optical 11 high-density mirror curtains
Memory Yes
Input power
For UL/cUL installations 9 to 15 VDC (12 V nominal)
10 to 15 VDC (12 V nominal)
Peak-to-peak ripple 2 V (at 12 VDC)
Detector start-up time 25 s 60 s
Normal current
For UL/cUL installations 6.5 mA
0.078 W
10 mA
—
Current in alarm 1.2 mA 3.8 mA
Maximum current
(LED on) 11 mA 24 mA
Mounting height 1.8 to 3.0 m (5.9 ft.to 9.8 ft.)
Target speed range 30 cm/s to 3 m/s
(1 ft./s to 10 ft./s)
20 cm/s to 3 m/s
(0.65 ft./s to 10 ft./s)
Alarm (NC) / Tamper
relay characteristic 80 mA, 30 VDC,
resistive
80 mA, 30 VDC
Pry-off tamper (not
evaluated by UL/cUL) Optional Onboard (yes)
AM relay characteristic — 80 mA
at 30 VDC max.
PIR Alarm time 3 s
Operating temperature
For UL/cUL installations −10 to +55°C (14 to 130°F)
0 to 49°C ( 32 to 120°F )
Dimensions (H x W x D) 125 Ч 55 Ч 60 mm
(4.92 x 2.16 x
2.36 in.)
125 Ч 65 Ч 60 mm
(4.92 x 2.6 x 2.36 in.)
VE1120 VE1120AM
Relative humidity 95% max. noncondensing
(UL/cUL Installations)
Weight 150 g
IP/IK rating IP30 IK02
Regulatory information
Manufacturer UTC Fire & Security Americas Corporation, Inc.
1275 Red Fox Rd., Arden Hills, MN 55112-6943, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, Netherlands
Certification
UL/cUL The product must be connected to a listed burglar
system compatible control unit or power supply unit,
which provides a minimum 4 hours of standby power
and has a voltage output between 10 and 15 VDC.
All wiring must be made according to National
Electrical Code, NFPA70, and CSA C22.1, Canadian
Electrical Code Part I, Safety Standards for Electrical
Installations.
Perform walk test at least one per year.
Use only a listed power-limited supply.
VE1120AM has not been evaluated by UL/cUL.
FCC Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna
• Increase the separation between the equipment
and receiver
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected
• Consult the dealer or an experienced radio/TV
technician for help
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
IC This Class B digital apparatus complies with Canadian
ICES-003.
2002/96/EC (WEEE directive): Products marked with
this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more
information see: www.recyclethis.info.
Contact information
www.utcfireandsecurity.com or www.interlogix.com