Interlogix 2-Button Crystal Keychain Touchpad - Manual (Page 2)

Page 2
2-Button Keychain Touchpad
2) Place the Panel in the program mode by removing
the Panel cover.
3) Using an alphanumeric touchpad, enter the learn
sensors mode, then press COMMAND.
4) Select the appropriate unsupervised group num-
ber (01, 03, 06, 07, 32) and press COMMAND.
5) Select the desired sensor number (1 through 32 for
CareTaker Plus, 1 through 40 for Security Pro
4000) you want assigned to the Keychain Touch-
pad and press COMMAND.
6) Trip the Keychain Touchpad by pressing and
holding the arm and disarm buttons together,
until the LED flashes. The Panel announces “Sen-
sor nn okay.”
7) Repeat steps 5 and 6 until all Keychain Touchpads
are learned.
8) Replace the Panel cover.
To learn Keychain Touchpads as Wireless Touchpads:
Note: If the system includes other wireless touchpads,
they must be programmed at this time, even if
they already exist in Panel memory. If existing
touchpads are not reprogrammed, they are deleted
from memory when pressing COMMAND after
entering the
learn touchpads mode.
1) Disarm the system to level 1.
2) Place the Panel in the program mode by removing
the Panel cover.
3) Using an alphanumeric touchpad, enter the learn
touchpads mode and press COMMAND. The
alphanumeric display reads PRESS TP 01 BYP.
4) Press the Keychain Touchpad arm and disarm
buttons together, until the LED flashes. The Panel
announces “N okay.”
5) Repeat step 4 until all Keychain Touchpads and
wireless touchpads are learned.
6) Replace the Panel cover.
Commander 2000 and Security Pro
2000
To learn Keychain Touchpads as sensors:
1) Disarm the system to level 1.
2) Remove the battery door.
3) Enter either the installer or dealer programming
code.
4) Select the appropriate unsupervised group num-
ber by pressing STATUS + nn (nn = 01, 03, 06, 07).
The Panel announces “Sensor level nn.”
5) Enter the desired sensor number (01 through 17).
6) Trip the Keychain Touchpad by pressing and
holding the arm and disarm buttons together,
until the LED flashes. The Panel announces “Sen-
sor nn okay.”
7) Repeat steps 4, 5, and 6 until all Keychain Touch-
pads are learned.
8) Replace the battery door.
To learn Keychain Touchpads as Wireless Touchpads:
1) Disarm the system to level 1.
2) Remove the battery door.
3) Enter either the installer or dealer programming
code.
4) Press STATUS + STATUS + n (n = touchpad ID
number 1, 2, 3, or 4).
5) Trip the Keychain Touchpad by pressing and
holding the arm and disarm buttons together,
until you see the LED flash. The Panel announces
“N okay.”
6) Repeat step 5 until all Keychain Touchpads are
learned.
7) Replace the battery door.
Testing Keychain Touchpad Operation
Test Keychain Touchpad operation by pressing the
buttons as described below:
1) Disarm Button - The Panel disarms to level 1.
2) Arm Button - With optional feature number F25
off:
ν
the Panel attempts arming from level 1 to level 2
ν
the Panel attempts arming from level 2 to level 3
ν
if protesting, the Panel responds as if BYPASS was
pressed
With optional feature number F25 on:
ν
the Panel arms directly to level 3, with no delay
ν
if protesting, the Panel responds as if BYPASS was
pressed
3) Arm and Disarm Buttons Together - The Panel
responds with an alarm condition as follows:
ν
Keychain Touchpads learned as sensors generate
an alarm based on the sensor group in which they
are learned
ν
Keychain Touchpads learned as wireless touch-
pads generate a police panic alarm (upper sensor
number 81)