Interlogix T-500-PIV - Manual (Page 3)

Keypad configuration card
1. Place the reader in tamper mode by briefly
removing and replacing the reader’s cover
while the power is on. The reader stays in
tamper mode for 60 seconds (minimum) after
power is applied or the cover is replaced.
2. Present the keypad configuration card within
one minute. The LED turns green and a short
triple-beep indicates the reader is ready to
configure.
3. Enter the keypad entry within five seconds.
Use the chart below to identify the correct
keypad entry.
FCC compliance
The FCC requires the following statement: This
reader uses radio frequency energy and has been
tested, and complies with the limits of FCC testing.
Changes, modification, or disregard of proper
installation and instructions not expressly approved
by UTC Fire & Security, and is strictly prohibited by
the FCC and could void the user’s authority to
operate the equipment.
Specifications
The voltage specification for this reader is 6—16
VDC, although 12 VDC or greater is recommended
for better performance and cable run distances.
Ordering information
Copyright © 2012, UTC Fire & Security. All Rights Reserved.
The Transition Series product name and logo are trademarks of
UTC Fire & Security. Other trade names used in this document
may be trademarks or registered trademarks of the
manufacturers or vendors of the respective products.
Document number: 460661001G - November 2012
Mode/Keypad entry Setting UTC
non-
UTC
1 * followed by 0
(Factory default
setting) 8 bits per key,
no buffering
 
2 * followed by 1 6 bits per key,
no buffering

3 # followed by
3 keys
(0 to 9 only) 26-bits output custom
configuration. (Contact
Sales Engineering/Pre-
Sales Support for
assistance)

4 1 followed by 1
key (0 to 9 only) 4 bits per key, no parity,
up to 9 keys buffered

5 1 followed by * 4 bits per key, no parity,
up to 10 keys buffered

6 1 followed by # 4 bits per key, no parity,
up to 11 keys buffered

For non-ITC keypad configurations, contact Sales
Engineering/Pre-Sales Support for assistance.
Colors Black
Power supply Linear DC recommended
Power usage T-500-PIV: 210 mA @ 12 VDC
T-520-PIV: 130 mA @ 12 VDC
T-525-PIV: 130 mA @ 12 VDC
Voltage range 6 —16 VDC
Temperature
range
a
-31 o F to +149 o F (-35 o C to +65 o C)
Cable distance to
panel Up to 500 ft. (152.4 m) @ 12 VDC with
20 AWG shielded cable
Read Range b
(Distances may
vary depending on
environment.)
Proximity Perfect and Ultralight cards
are not supported by the Transition
Series reader.
Model T-500-PIV:
- Proximity: up to 3.5" (8.89 cm)
- HID Proximity: up to 3.5" (8.89 cm)
- PIV: up to 1" (2.54 cm)
Model T-520-PIV and T-525-PIV:
- Proximity: up to 5" (15.24 cm)
- HID Proximity: up to 5" (15.24 cm)
- PIV: up to 1" (2.54 cm)
Wiegand output Proximity 4002 (40-bit)
HID Proximity (depends on card
format)
PIV (75-bit and 200-bit)
Tamper output Open Collector
Regulatory
approvals and
standards UL 294, CE, and FCC (part 15)
ISO Standards ISO 14443A, B
UL evaluation for UL Listed Installations:
a. -25 o F to 125 o F (-32 o C to 52 o C)
b. Model T-500-PIV, T-520-PIV and T-525-PIV
Proximity and HID Proximity up to 4.5" (11.43 cm)
c. Power consumption:
Model 500-PIV: 210 mA @ 12 VDC
Model 520-PIV and 525-PIV: 130 mA @ 12 VDC
d. Request to exit terminals on the reader are not to
be connected in UL listed installations.
Product Part Number
T-500-PIV (Black; Mullion mount; Wiegand
output) * 430212006
T-520-PIV (Black; 1-Gang US mount;
Wiegand output) * 430213006
T-525-PIV (Black; 1-Gang US mount;
Keypad; Wiegand output) * 430214006
* Installation wrench (Required) 385001001