Vermont Casting 39LDVR - Manual (Page 2)

FIREPLACE & VENTING SPECIFICATIONS
PERFECTVIEW 39LDVR REAR VENT
VENT SECTIONS
NOTE: THE INSTALLED LENGTH OF ANY VENTING SECTION IS 1 1/2 ” LESS THAN ITS TOTAL
LENGTH, EXCEPT FOR THE LAST SECTION INSTALLED.
12"
305mm
24"
610mm
36"
914mm
48"
1219mm
7TDVP8 7TDVP12 7TDVP24 7TDVP36 7TDVP48 7TDVP1218 7TDVP3564
8"
203mm
7"
178mm
35"
889mm
64"
1626mm
12"
305mm
18"
457mm
9 1/4 "
7 1/4 "
9 1/4 " 90 °
7"
13"
9 1/4 "
90 °
13"
7 1/4 "
13"
17"
OFFSET
235mm
235mm
178mm
184mm
330mm
330mm
335mm
330mm
184mm
OFFSET w/2-90 °
Back to Back
FIREPLACE FACTS
Minimum Mantel Clearances
Mantel Depth
2”
4”
6”
8”
10”
Clearance From Top
of Combustion Chamber Opening
To Bottom of Mantel
9”
11”
13”
15”
17”
CONTEMPORARY TERMINATIONS
7TDV45
7TDVRT90
11"
7 3/8 "
45 °
45 °
7 3/8 "
OFFSET w/2-45 °
Back to Back
45 ° 7 3/8 "
188mm
188mm 188mm
FP890
FP889
ELBOWS
7TDVRVT
7TRVT
9³⁄₄ "
12¹³⁄₁₆" 7"
7TDVSKV
9¹⁄₂ "
7"
13³⁄₁₆"
7TDVSKS
32"
6 1/2 "
813mm
127mm
19"
16"
482mm
406mm
165
mm
5"
FEATURES:
• 39” PerfectView Direct Vent Gas Appliance
• 16,000 to 23,000 BTU/hr. input
• Patented Insta-Flame TM Ceramic Burner System with 4-piece
Split Oak Ceramic Fiber Log Set
• Tempered Glass Panel Assembly
• Adjustable Flame and Heat Output
• Wall Switch
• 18” Flex Connector with Shutoff and EB1 electrical box installed
• Wall Firestop, Zero Clearance Sleeve (Rear vent models only)
• Rated as Fireplace Heater (AFUE)
• Uses 4”/7” Majestic (Direct Vent) Venting Components
BURNER SYSTEM:
• Capacity – Natural: 23,000 BTU/HR Max.
16,100 BTU/HR Min.
– Propane: 22,500 BTU/HR Max.
16,875 BTU/HR Min.
• Fuel - Natural or Propane Gas
• Ignition System - Standing Pilot With Piezo Ignitor, A Low
Voltage, Self-Generate Power Pile System (mV)
– No Outside Electrical Power Needed OR
– Electronic ignition that requires 120 VAC
Electrical hook up.
• Gas Supply Line - Consult Gas Code Book for Correct Sizing
• Gas Inlet and Manifold Pressures
Natural Propane
Minimum Inlet Pressure 5.5” w.c. 11.0” w.c.
Maximum Inlet Pressure 14” w.c. 14.0” w.c.
Manifold Pressure 3.5” w.c. 10.0” w.c.
MINIMUM FLOOR AREA:
• 39” W X 16” D
HEARTH EXTENSION:
A Hearth Extension Is Recommended But Not Required
ACCESSORIES:
39LDVCR - 39” LDV Ceramic Refractory
FK12 - Fan and Cord (160cfm) (for RN/RP only)
FK24 - Variable Speed Heat-Activated Fan Kit
IMTFK - IMT Thermostat w/ Face Plate
PerfectView 39LDVR
39LDVR
FLUE SYSTEM
7” Coaxial Direct Vent System
SPECIFICATIONS:
• 7” O.D.
• 4” I.D.
MINIMUM CLEARANCE TO COMBUSTIBLE MATERIAL
a) Rear Wall Vent Applications 2” top, 1” Sides & Bottom
b) Vertical Side Wall Applications 1” to All Sides
c) Vertical thru the Roof Applications 1” to All Sides
MINIMUM COMBUSTIBLE WALL/FLOOR OPENINGS
a) 9 3/8” x 10 3/8” H for Rear Wall Vent Applications
b) 9 3/8” W x 9 3/8” H for Vertical Side Wall/Vertical Ap-
plications
MAXIMUM INSTALLATION LENGTHS
a) Rear Wall Vent Applications
20” (508mm) Vent Length
20” (508mm) Vent Length with one 45° elbow
b) Vertical Side Wall Applications
20’ (6 m) Horizontal Vent Length with
7.5’ (2.29 m) vertical rise
*Refer to manual for alternative venting distance
VERTICAL THRU THE ROOF APPLICATIONS
8’ (2.4 m) Minimum Vertical Rise
40’ (12 m) Maximum Vertical Rise
2 sets of 45° Elbows can be used in Vertical rise
with 8’ maximum distance between elbows
Two 90° elbows maximum for 10’ (3 m)
Horizontal can be installed in Vertical
Applications
*Maximum angular variation for Vertical Sidewall/Vertical
Application in system is total of 270°
*Refer to installation manual for all venting restrictions
with elbow use
TERMINATION CLEARANCES MINIMUM
a) Horizontal
12” (305 mm) above Grade Level
18” (458 mm) to Ventilated Soffi t
12” (305 mm) to Unventilated Soffi t
12” (305 mm) under veranda, porch, deck or balcony
b) Vertical
24” (610 mm) Above a Roof Surface and any other
obstruction within a horizontal distance
of 18” (458 mm)
*Refer to installation manual for more termination
restrictions and clearance information
39LDVR ANSI Z21.88 - 2005/CSA 2.33 2005
Vented Gas Fireplace Heaters
This gas appliance should be installed by qualifi ed
installers in accordance with local building codes
and the current National Fuel Gas code ANSI Z223.1
or CSA B 149.1 Installation code for Gas Burning
Appliance and Equipment.
PRODUCT LISTING
1118mm
686mm
419mm
406mm
889mm 870mm
1581mm
790mm
1118mm
172mm
235mm
991mm
1003mm
946mm
584mm
27 3/4 ”
708mm
83mm
476mm
302mm
203mm
143mm
24 1/4 ”
616mm 51mm 51mm
REV. 10/07
The Fireplace Facts Information Sheets are for
quick reference only and are subject to change with-
out notice. Actual fi replace instructions must abide
by specifi cations provided with each product.
ACCESSORIES (Continued):
(continued from second page)
WALL FRAMING DIMENSIONS
Vent Opening for
Combustible Wall
• Louver Kits - Additional Louver Kits ( To replace all louvers in
desired color, 4 sets are required ) See Price List
• Filligree Louver Kits - See Price List
• Perimeter Trim Kits - See Price List
• Face Trim Kits - See Price List
• NEW - Bulk Flex Kits - see Price List
Framing Detail
9 ³⁄₈"
(240 mm)
10 ³⁄₈"
(264 mm)
VO584-100
Fireplace Hearth
Rnd.
7¹⁄₂" Dia.
(190 mm)
Opening for Non-combustible Wall