MUTEC MC-7 - Manual (Page 10)

\\\\\\\\\\\\\
C O N T R O L E L E M E N T S C O N T R O L E L E M E N T S C O N T R O L E L E M E N T S
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
> > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > 88 10
1 WCLK OUT 1–3
These 3 pairs of Word Clock outputs transfer either all standard Word Clock
rates as well as so-called »Super Clock« rates (Word Clock x 256) for older
Digidesign ProTools™ systems. Their numbering is aligned to the functional
menu »CLK
MULTIPLIERS « on the front panel. The individual BNC connectors of
an output pair are marked as A and B. This allows, for example, for a simple
documentation of the connected devices. For adjusting these outputs see
chapter OPERATING THE MC-7.
2 S/P-DIF OUT 6
These two S/P-DIF outputs, available as optical (»OP«) and coaxial (»CO«)
interfaces, transmit an optical S/P-DIF and an unbalanced electrical S/P-DIF
digital audio or blank frame signal in compliance with the IEC 60958 stand-
ard. Their numbering is aligned to the corresponding functional menu on the
front panel. For adjusting these outputs see chapter OPERATING THE MC-7.
3 AES3/11 OUT 5
This AES/EBU output transmits a transformer-balanced electrical AES3 or
AES11 signal. Its numbering is aligned to the corresponding functional
menu on the front panel. For adjusting this output see chapter OPERATING
THE MC-7.
4 AES3/11 IN
This AES/EBU input can receive a balanced digital AES3 or AES11 signal in
compliance with AES3 –1992 (R1997) or AES11–1997/2003. The input imped-
ance is 110 Ω (XLR connector, female). For selecting this input see chapter
OPERATING THE MC-7.
5 S/P-DIF IN
These two S/P-DIF inputs, available as optical (»OP«) and coaxial (»CO«)
interfaces, receive an optical S/P-DIF and an unbalanced electrical S/P-DIF dig-
ital audio or blank frame signal in compliance with the IEC 60958 standard.
For selecting one of these inputs see chapter OPERATING THE MC-7.
6 WCLK IN
This input can receive a Word Clock or so-called »Super Clock« (Word
Clock x 256) signal. The impedance of the connector is 75 Ω (BNC connectors,
female). For selecting this input see chapter OPERATING THE MC-7.
7 MAINS IN, Power Switch + Power Inlet
This is the main switch for switching the device on and off. Be sure to
make all connections (especially the supplied power cable) properly before
turning on the switch. Heed the SAFETY INSTRUCTIONS at the beginning of
this manual.
Connect the supplied power cable here. Make sure that the power switch
is turned off before connecting the power cable to this inlet and to the
power outlet. Line voltages within the range of 90…260V with a frequen-
cies between 47...440Hz can be applied. The internal power supply will
automatically make all necessary adjustments.
MC-7 Rear Panel
For detailed specifications on all terminals,
refer to the »Pin Assignment of the
Connectors« and »Technical Data« in the
chapter »APPENDIX«.
1 2 3 4 7 5 6