Vitek VT-3606 - Manual (Page 5)

INSTALLATION EXAMPLE (FIG.1,2,3,4)
Installing in a dashboard
1. Remove the screws and clips.
3. CLIP. Break off these clips if necessary.
Note: Store the key in a reliable place, as you
may need to remove the device from the car in
the future.
Removal and installation of the front panel
The front panel of this device can be removed in
order to avoid theft.
REMOVING THE FRONT PANEL (Fig. D)
Before removing the deck’s front panel, turn off
the power by pressing button 1 – POWER
ON/OFF (“PWR”).
Press the panel release button 16 to remove the
front panel (“REL”), pull the panel towards your-
self.
See the figure D.
INSTALLING THE FRONT PANEL (Fig. E)
Before installing the panel, make sure that it is
located in the correct position. Connect side B
of the panel with side A of the main unit. Push
the panel into place until it clicks.
Notes:
• Do not press too hard when installing the panel.
It freely snaps into place with light pressure.
• When taking the panel with you, place it in the
supplied case.
• Do not press hard on the LCD screen when con-
necting the front panel to the main unit.
1. POWER ON/OFF ( )
Press this button to turn the device on. To turn it
off, press and hold this button for more than 1
second. This device turns on when any button is
pressed.
2,3. MENU SETTINGS BUTTONS: BASS/TRE-
BLE/CHANNEL BALANCE/ FADER
When pressed momentarily, the sound charac-
teristics setting mode is activated.
VOLUME—- BASS—— TREBLE—— CHANNEL
BALANCE—— FADER—— VOLUME
Rotate knob 3 to set the desired parameters
VOLUME, BASS, TREBLE, CHANNEL BALANCE,
FADER.
TA SEEK /TA ALARM (2)
Press the SEL button for more than 2 seconds to
activate the function selector for traffic notifica-
tion messages.
The TA SEEK or TA ALARM functions can be
chosen by rotating the VOL knob.
- TA SEEK mode:
If a newly tuned station does not transmit traffic
information within 5 seconds, the radio automat-
ically tunes to the next station that transmits
traffic information.
In TA search mode, the current station can be
switched to another station if the signal is lost or
the station stops broadcasting traffic informa-
tion, because the device is searching for other
stations, broadcasting traffic information, that
have strong broadcast signals and are transmit-
ting TP-signal information.
- TA ALARM mode:
This mode automatically switches to a station
transmitting traffic information and sounds a
warning beep before the beginning of the traffic
information broadcast.
MASKING OF ALTERNATIVE FREQUENCIES
(“MASK DPI”) (2)
Holding down the “SEL” button for more than 2
seconds activates the selection of alternative
frequencies processing mode.
MASK DPI mode: masks radio stations on
alternative radio frequencies (AF) that have dif-
fering program identifiers (PI).
MASK ALL mode: masks radio stations on
alternative radio frequencies with differing pro-
gram identifiers and no RDS signal.
RETUNING STATIONS (“L / S”) (2)
Pressing the SEL button for more than 2 sec-
onds activates the function selector for the
retune mode, which retunes to stations transmit-
ting traffic information.
RETUNE L: Sets the TA search mode delay to
90 seconds.
RETUNE S: Set the TA search mode delay to 30
seconds.
AUDIO PROCESSOR (“AUDIO DSP”) (2)
Pressing the “SEL” button for more than 2 sec-
onds activates the function selector for the
audio processing parameters.
The parameters are chosen using the 3 (“VOL”)
knob in the following order:
POP M—-ROCK M—-CLASSICAL—- NEUTRAL
MUSIC—-PROCESSOR OFF
ENGLISH
5
3606_4l.qxd 29.03.05 13:40 Page 5