Reznor SSCDBL Parts Manuals - Manual (Page 3)

Form P-SC, P/N 269822R3, Page 3
Date Series was Introduced or Re-certified (may affect parts
selection)
Series changes indicate when that Model was recertified by the approval
agency. The Series is identified in the Model No. of the unit. The number
following the model of the heater is the series number (Example: SC300-
6, "6" is the Series No.). Replacement parts may be affected by the
introduction of a new series.
NOTE: Series 6 had significant changes. Replacement parts specific
to Series 1, 3, and 5 are not listed in this manual and are no longer
available.
Model SSCDBL replacement parts are not
specifically listed. Look for the equivalent SSCBL
Model as listed below.
Two BL Blower Cabinets
- All Sizes
2 Furnace Sections - Size 800
4 Furnace Sections - Sizes
1000, 1200, 1400, 1600
NOTES: Manufacture of Models SCA and SCB was discontinued in 2001. Replacement parts are not listed in this manual and may
not be available. If a part is needed, contact your distributor for availability.
Manufacture of Model SCE was discontinued in 2011.
Introduction - Month/Year (Serial No. Date Code) of Furnace Certification
Models Series 1 Series 3 Series 5 Series 6
ANSI
Std
SC 3/74 (ZC) 9/82 (AHI) 4/89 (AOD) 10/93 (ASJ)
SCA 3/74 (ZC) 9/82 (AHI) 4/89 (AOD) 10/93 (ASJ)
SCB 3/74 (ZC) 9/82 (AHI) 4/89 (AOD) 10/93 (ASJ)
SCE 8/74 (ZH) 9/82 (AHI) 4/89 (AOD) 10/93 (ASJ)
SSCBL 1/92 (ARA) 1/97 (AWA)
C.G.A.
Std
SC 3/75 (AAC) -- -- 10/93 (ASJ)
SCA 3/75 (AAC) 9/82 (AHI) 1/91 (AQA) 10/93 (ASJ)
SCB 3/75 (AAC) 9/82 (AHI) 1/91 (AQA) 10/93 (ASJ)
SCE -- 9/82 (AHI) 1/91 (AQA) 10/93 (ASJ)
SSCBL 1/97 (AWA)
SSCDBL Consists of:
800 (2) Model SSCBL 400 Packaged Systems
1000 (2) Model SSCBL 500 Packaged Systems
1200 (2) Model SSCBL 600 Packaged Systems
1400 (2) Model SSCBL 700 Packaged Systems
1600 (2) Model SSCBL 800 Packaged Systems
Model SSCDBL Configuration
Blower Cabinet Rating Plate on Certified Packaged Units
Key to Blower Cabinet Plate
A = Standard
B = Model
C = Date of Manufacture
D = Motor Horsepower
E = Volts/Phase/Hertz/Amps
F = SCFM
G = Static Pressure (w.c.)
H = Drive AM Option Code
I = Wiring Diagram No.
REZNOR
MERCER, PA., U.S.A. 16137
PACKAGED DUCT FURNACE
FOR INDUSTRIAL/COMMERCIAL USE ONLY
DESIGN CERTIFIED FOR A.G.A REQUIREMENTS UNDER
[ A ] PACKAGED DUCT FURNACE STANDARD
MODEL [ B ] [ C ]
SERIAL NO. [ D ] HP
[ E ] VOLTS [ E ] PH [ E ] HZ MAXIMUM TOTAL INPUT [ E ] AMPS
IF EQUIPPED WITH REC OPTION, ADD [ V ] AMPS
EQUIPPED FOR OPERATION AT AN AIR FLOW OF [ F ] SCFM
AGAINST A STATIC PRESSURE OF [ G ] INCHES WATER COLUMN.
DRIVE NO. [ H ] WIRING DIAGRAM [ I ]
SEE MANUFACTURER'S INSTRUCTIONS FOR OTHER AIR FLOW
CAPACITIES.
FILTERS, WHEN USED, MUST BE INSTALLED EXTERNAL TO THE
HEATER CASING.
REFER TO THE RATING PLATE OF THE DUCT FURNACE FOR
ADDITIONAL INFORMATION.
Identification
Plate on
Blower
Cabinets
Manufactured
Prior to
Package
Certification
(see dates
below)
®
MODEL NUMBER SERIAL NUMBER
DRIVE NO. WIRING DIAGRAM NO.
CFM _____ AT____ IN. W.C. MAX. E.S.P. AND ____ HP
VOLTS PHASE HERTZ AMPERES
Replacement Parts Tag
HP Codes:
Each unit may have a replacement parts tag that includes the Model No. and the Serial No. as well
as a list of original common replacement parts. Always provide the full model and serial numbers
when ordering replacement parts.
Vent Terminal/Combustion Air Intake Components -
applies to all "SC" Series Models (one per furnace)
Code 3 - Concentric Adapter Assy for Separated
Combustion Installation -- required on all Models
Code 5 - Inlet
Guard for
Horizontal Inlet
(replaces inlet
screen)
Code 7 -
Screened
Exhaust Cap
for Horizontal
Vent
Code 8 -
Inlet Air
Cap for
Vertical
Inlet
Code 9 -
Exhaust
Cap for
Vertical
Vent
Heater
Side
Terminal
Side
Code Qty P/N Description
1 1 205883
Complete Horizontal Vent Terminal/Combustion
Air Kit (Same as Option CC6) includes Codes
3, 4, 5, 6, 7, 10
2 1 205896
Complete Vertical Vent Terminal/Combustion
Air Kit (Same as Option CC2) includes Codes
3, 4, 6, 8, 9, 10
Components:
3 1 205885 Concentric Adapter Box Assy (CC2 & CC6)
4 2 207232 Concentric Adapter Box Bracket (CC2 & CC6)
- not illustrated
5 1 205894 Inlet Guard for Horizontal (Option CC6)
6 4 37661 #10-16 x 1/2" lg Screws to attach CODE 5
7 1 53316 Screened Exhaust for Horizontal (Option CC6)
8 1 53330 Inlet Air Cap for Vertical (Option CC2)
9 1 110052 Exhaust Cap for Vertical (Option CC2)
10 1 53335 Tube of High Temperature (450°F) Silicone
Sealant (not illustrated)
Single-Speed Motors 2-Speed Motors
Code HP Code HP
05 1 20 1/.44
06 1-1/2 21 1.5/.68
07 2 22 2/.88
08 3 23 3/1.3
09 5 24 5/2.2
11 7-1/2 25 7.5/3.3
12 15 26 10/4.4
13 10
14 20