Cypress CY14B101Q3 - Manual (Page 13)

PRELIMINARY
CY14B101Q1
CY14B101Q2
CY14B101Q3
Document #: 001-50091 Rev. *A Page 13 of 22
Maximum Ratings
Exceeding maximum ratings may shorten the useful life of the
device. These user guidelines are not tested.
Storage Temperature ................................. –65
°C to +150°C
Maximum Accumulated Storage Time
At 150 °C Ambient Temperature........................ 1000h
At 85 °C Ambient Temperature..................... 20 Years
Ambient Temperature with
Power Applied ............................................ –55 °C to +150°C
Supply Voltage on V
CC
Relative to GND ........–0.5V to +4.1V
DC Voltage Applied to Outputs
in High-Z State....................................... –0.5V to V
CC
+ 0.5V
Input Voltage.......................................... –0.5V to V
CC
+ 0.5V
Transient Voltage (<20 ns) on
Any Pin to Ground Potential .................. –2.0V to V
CC
+ 2.0V
Package Power Dissipation
Capability (T
A
= 25°C) ................................................... 1.0W
Surface Mount Lead Soldering
Temperature (3 Seconds) .......................................... +260 °C
DC Output Current (1 output at a time, 1s duration).....15 mA
Static Discharge Voltage.......................................... > 2001V
(per MIL-STD-883, Method 3015)
Latch-up Current.................................................... > 200 mA
Table 9. Operating Range
Range Ambient Temperature V
CC
Commercial 0 °C to +70°C 2.7V to 3.6V
Industrial –40 °C to +85°C 2.7V to 3.6V
DC Electrical Characteristics
Over the Operating Range (V
CC
= 2.7V to 3.6V)
Parameter Description Test Conditions Min Max Unit
I
CC1
Average V
cc
Current At f
SCK
= 40 MHz 10 mA
I
CC2
Average V
CC
Current
during STORE
All Inputs Don’t Care, V
CC
= Max.
Average current for duration t
STORE
10 mA
I
CC4
Average V
CAP
Current
during AutoStore
Cycle
All Inputs Don’t Care, V
CC
= Max.
Average current for duration t
STORE
5 mA
I
SB
V
CC
Standby Current 5 mA
I
IX
[4] Input Leakage Current
(except HSB)
V
CC
= Max, V
SS
< V
IN
< V
CC
–1 +1 µA
Input Leakage Current
(for HSB)
V
CC
= Max, V
SS
< V
IN
< V
CC
–100 +1 µA
I
OZ
Off State Output
Leakage Current
V
CC
= Max, V
SS
< V
OUT
< V
CC
–1 +1 µA
V
IH
Input HIGH Voltage 2.0 V
CC
+ 0.5 V
V
IL
Input LOW Voltage V
SS
– 0.5 0.8 V
V
OH
Output HIGH Voltage I
OUT
= –2 mA 2.4 V
V
OL
Output LOW Voltage I
OUT
= 4 mA 0.4 V
V
CAP
[5] Storage Capacitor Between V
CAP
pin and V
SS
, 5V Rated 61 180 µF
Notes
4. The HSB pin has I
OUT
= -2 uA for V
OH
of 2.4V when both active high and LOW drivers are disabled. When they are enabled standard V
OH
and V
OL
are valid. This
parameter is characterized but not tested.
5. V
CAP
(Storage capacitor) nominal value is 68 uF.
[+] Feedback