Configurations, Con ne ct to +1 2v o nly powe rcable, Speed out / sense in cable – TeeJet Matrix 840G User Manual User Manual
Page 10
5
98-05188 R2
www.teejet.com
Configurations
The following diagrams are reflective of typical Matrix configurations. Due to the variety of possible
configurations, these should be used for reference purposes only.
Figure 1-14: Matrix w/RealView Camera
16-00022 RealView Camera
C
on
ne
ct
to
+1
2v
O
nly
Powe
rCable
45-05645
Power
Cable, 12V
45-05775
3 m Power
Cable, Battery
CAUTION CONN.
TO +12V ONLY
PO
W
ER CABLE
45-
05775
DC: X
XX
X
8 Pos.
4 Pos.
8 Pos.
Camera
45-05617: 6 m
45-05618: 18 m
Camera Extension Cable
5 Pos.
Matrix 570G
75-30055
75-30056 w/ClearPath
Matrix 840G
75-30070
75-30071 w/ClearPath
78-50155
GPS Ant.
Kit, RAM Mount w/Suction Cup
90-02349 (Matrix 570G)
90-02700 (Matrix 840G)
Ma
trix
GPS
Speed
Work On-Off
78-00044 xx/xx
78-00044: 4 Pos.
78-00046: 8 Pos.
Switch Box
Work On-Off Switch
Matrix
FieldPilot
BoomPilot
Optional Accessory
Speed Out / Sense In Cable
The Speed Out / Sense In Cable assists the Matrix with two additional connections that::
►Send a radar speed signal to an external device
►Allow the user to operate the area applied function of the Matrix in series with a remote master
connection or existing apply on/off toggle in a single swath manner. However if the previous connections
are not available the supplied toggle switch allows area applied functionality without the need to connect
to a functional application implement.
Connecting to different consoles requires different adapters and calibrations.
• If connecting to TeeJet consoles use speed adapter 45-20042
◄enter calibration # 914 (#1000 in Europe) for 8xx series in RAD mode,
◄enter calibration # 9140 (#10000 in Europe) for below LH 70 Series, LH 85, 500 series, 5000,
6000, IC 24 and IC 34
• If connecting to Mid-Tech consoles no adapter is required,
◄enter calibration # 1000
• If connecting to Raven consoles use speed adapter 45-05508 (do not connect the 12v red wire
from 45-05508)
◄enter calibration # 730 in SP 2
If sensing boom shut-off for applied mapping from an existing console, attach the green wire to the valve
side of the master switch on the console. The red wire is not used.
Figure 1-15: Matrix w/8 Channel or 4 Channel VSM & Multiple RealView Cameras
PO
W
ER
IN
C
AN
RS-232
Po
w
er/
D
AT
A
45
-0
56
26
45-05626
Power/CAN/Data
Cable
(included with
FieldPilot kits)
3A Fuse
8 Pos.
RS-232
TJ CAN
(Terminated)
C
A
U
TI
O
N
: C
O
N
N
E
C
T
TO
1
2V
O
N
LY
P
ow
er
C
ab
le
40
1-0
01
6
D
C
: x
x/x
x
W
A
R
N
IN
G
C
O
N
N
E
C
T
D
IR
E
C
TL
Y
T
O
B
AT
.
401-0016
Battery Adapter
45-08101
CAN Terminator
16-00022
RealView Camera
78-08067
Video Selector Module,
4CH Video CAN
78-08068
Video Selector Module,
8CH Video CAN
4 Pos.
8 Pos.
Camera
45-05617: 6 m
45-05618: 18 m
Camera Extension Cable
5 Pos.
Matrix 570G
75-30055
75-30056 w/ClearPath
Matrix 840G
75-30070
75-30071 w/ClearPath
78-50155
GPS Ant.
Kit, RAM Mount w/Suction Cup
90-02349 (Matrix 570G)
90-02700 (Matrix 840G)
Ma
trix
GPS
Speed
Work On-Off
78-00044 xx/xx
78-00044: 4 Pos.
78-00046: 8 Pos.
Switch Box
Work On-Off Switch
45-05786: 6 m
45-05787: 9 m
Antenna Cable
78-50187
Optional RXA-30 GPS Antenna
65-05226
Kit, Bracket
RXA-30 Antenna
Matrix
FieldPilot
BoomPilot
Optional Accessory