Casio 5060 - Manual (Page 3)

Operation Guide 5060
3
Mode Reference Guide
Your watch has five “modes”. The mode you should select depends on what you want
to do.
To do this: Enter this mode:
View the current date in the Home City •
Configure Home City and daylight saving time •
(DST) settings
Perform a time calibration receive operation •
Configure time and date settings manually •
Timekeeping Mode
Use the stopwatch to measure elapsed time Stopwatch Mode
Use the countdown timer Countdown Timer Mode
View the current time in one of 29 cities (29 time
zones) around the globe
World Time Mode
Set an alarm time Alarm Mode
Selecting a Mode
With this watch, everything starts from the Timekeeping Mode.
To determine the watch’s current mode
Check the position of the v Left Dial Hand as shown
under “To select a mode”.
To return to the Timekeeping Mode from any other
mode
Hold down C for about two seconds until the watch beeps
twice.
To select a mode
Press C to cycle between the modes as shown below. The v Left Dial Hand
indicates the currently selected mode.

>
>
Timekeeping Mode Stopwatch Mode
Alarm Mode
Countdown Timer Mode
World Time Mode
The hand indicates
the day of the week
(SU, MO, TU, WE, TH,
FR, SA).
The hand points to ST (at
12 o’clock).
The hand points to AL.
The hand points to TMR.
The hand points to STD
or DST.
C
Timekeeping
Use the Timekeeping Mode to view the current time and date. To enter the
Timekeeping Mode from any other mode, hold down C for about two seconds.
Hand Functions
z
Hour Hand
x Second Hand
c Minute Hand
v Left Dial Hand: Indicates the day of the week.
b Lower Dial Hand: Indicates the current hour in the
Home Time city in 24-hour format.
n Right Dial Hands:
Indicate the current time in the World Time City in
24-hour format.
m Day

B +
* 6 > 5
@
Configuring Home City Settings
There are two Home City settings: actually selecting the Home City and selecting
either standard time or daylight saving time (DST).
To configure Home City settings
Note
This watch does not have a city code that •
corresponds to Newfoundland.
In the Timekeeping Mode, keep 1. A depressed (for about
five seconds) as the x Second Hand goes through the
following sequence.
Moves to the last signal reception result ( • Y or N), then
to READY (or R for some models), and then to the city
code of the currently selected Home City.
This indicates the city code setting mode.
•
The watch will exit the setting mode automatically if •
you do not perform any operation for about two or
three minutes.
For details about city codes, see the “City Code •
Table”.
To change the Home City setting, press 2. D to move the
x Second Hand clockwise.
Keep pressing • D until the x Second Hand is pointing
at the city code you want to select as your Home City.
Each time you select a city code, the • z Hour Hand,
c Minute Hand, b Lower Dial Hand and m Day
move to the current time and date for that city code.
Do not perform the next operation until these hands
stop moving.
Press 3. B to toggle the time for the currently selected city code between STD
(standard time)/ DST (daylight saving time).
In the city code setting mode, the • v Left Dial Hand indicates the current daylight
saving time setting as STD (standard time) or DST (daylight saving time).
Note that you cannot switch between • STD (standard time)/DST (daylight saving
time) while UTC is selected as your Home City.

@

B +
* @ 5 >
After all the settings are the way you want, press 4. A to return to the Timekeeping
Mode.
To toggle the Home City time between standard time and daylight saving time
Perform the step 1 under “To configure Home City settings”. 1.
Each time you select a city code, the • z Hour Hand, c Minute Hand, and
b Lower Dial Hand move to the current time for that city code. Do not perform
the next operation until these hands stop moving.
Press 2. B to toggle the time for the city code of the currently selected Home City
between STD (standard time)/DST (daylight saving time).
In the city code setting mode, the • v Left Dial Hand indicates the current daylight
saving time setting as STD (standard time) or DST (daylight saving time).
Note that you cannot switch between • STD (standard time)/DST (daylight saving
time) while UTC is selected as your Home City.
After all the settings are the way you want, press 3. A to return to the Timekeeping
Mode.
Note
After you specify a city code, the watch will use UTC* offsets in the World Time •
Mode to calculate the current time for other time zones based on the current time
in your Home City.
Coordinated Universal Time, the world-wide scientific standard of timekeeping. *
The reference point for UTC is Greenwich, England.
Selecting some city codes automatically makes it possible for the watch to •
receive the time calibration signal for the corresponding area. See “Radio
Controlled Atomic Timekeeping” for details.
Configuring Current Time and Date Settings Manually
You can configure current time and date settings manually when the watch is unable
to receive a time calibration signal.
To change the current time setting manually
In the Timekeeping Mode, keep 1. A depressed (for about
five seconds) as the x Second Hand goes through the
following sequence.
Moves to the last signal reception result ( • Y or N), then
to READY (or R for some models), and then to the city
code of the currently selected Home City.
At this time, the
• v Left Dial Hand will indicate the
Home City’s current daylight saving time setting (STD
or DST).
Change the Home City and daylight saving time (DST) 2.
settings, if you want.
For details about these settings, see steps 2 and 3 •
under “To configure Home City settings”.
In the following steps, each press of
• C cycles
between settings as shown below.
Press 3. C .
The watch will beep, and the • x Second Hand and
v Left Dial Hand will move to their 12 o’clock
positions. This is the time setting mode.
Use 4. D (+) and B (–) to change the time (hour and minute) setting.
Each press of either button will move the hands ( • z Hour Hand and c Minute
Hand) to one minute.
Holding down • D or B will start high-speed z Hour Hand and c Minute Hand
movement in the applicable direction. To stop high-speed hand movement,
press any button.
The
• b Lower Dial Hand and z Hour Hand move in sync with each other.
When setting the time, make sure that the • b Lower Dial Hand indicates the
proper a.m./p.m. hour.
If you want to change the date setting at this time, press
• C and perform the
procedure starting from step 3 under “To change the current date setting
manually”.
After the time setting is the way you want, press 5. A to return to the Timekeeping
Mode.
This will cause the • x Second Hand to move automatically to 12 o’clock and
resume movement from there.
To change the current date setting manually
In the Timekeeping Mode, keep 1. A depressed (for
about five seconds) as the x Second Hand goes
through the following sequence.
Moves to the last signal reception result ( • Y or N),
then to READY (or R for some models), and then to
the city code of the currently selected Home City.
Press 2. C twice.
The watch will beep and change to the year setting •
mode.
The year can be set in the range of 2000 to 2099.
•
Use 3. D and B to change the year setting.
Each press of • B will move the v Left Dial Hand and
change the tens digit of the year setting.
Each press of • D will move the x Second Hand and
change the ones digit of the year setting.
After the year setting is the way you want, press 4. C .
The watch will beep and change to the month setting •
mode.

@ >

B +
* >
@
>
00
50
10
40
20
30
90
60
80
70
Setting the year (tens digit)
Setting the year (ones digit)
@ 0 1 2
3
4
6 5 7
9
8
Home city/DST Hour/Minute Year
Day Month