Document Outline

• Feature Guide
  • How The Manual Is Organized
  • The P/I-P55SP3AV Package
    • Bundled Software
  • Main Features
  • Static Electricity Precautions
  • Mainboard Layout
  • Using Your Mainboard
    • Hardware Settings
      • Jumpers and caps
    • Jumper cap 3-pin jumper 2-pin jumper Jumper block
      • Jumper diagrams
    • The System Configuration Record
      • Important:
      • System IRQs
      • BIOS-Supported Enhanced IDE Features
        • Other IDE Devices
        • Faster Data Transfer
      • Power Conservation
      • Audio Features
      • On-Board Video Display
      • SCSI BIOS Firmware & The Optional SC-200 Controller Card
• Upgrade Guide
  • InstalUng Expansion Cards
    • Installation Procedure
    • Assigning System IRQs for Expansion Cards
      • Assigning DMA Channels For ISA Cards
  • Upgrading System Memory
    • Configuring System Memory
      • Memory Combinations
    • Installing SIMMs
      • Installing a Memory Module
      • Module Sockets & Orientation
  • Updating the Flash BIOS
    • BIOS With Boot Block Update Procedure
• Software Guide
  • Award BIOS Setup
    • Main Program Screen
    • Standard CMOS Setup
      • Standard CMOS Setup Screen
      • Date & Time
      • Hard Drive Type
      • Floppy Disk Drives
      • Video Display Types
      • Error Handling
      • BIOS Features Setup
        • BIOS Features Setup Screen
        • Virus Protection
        • Cache Control
        • Boot Up Features
        • IDE Block Mode
        • Keyboard Interface
        • Security Option Password Control
        • PS/2 Mouse
        • Shadow Controls
      • Chipset Features Setup
        • Chipset Features Screen
      • Power Management Setup
        • The Power Management Setup Screen
        • Power Management
        • t^ideo Off
        • Suspend Switch
        • Doze & Standby Speeds
        • PM Timers
        • PM Events
        • IRQ3 to IRQ1S Individual Settings
        • PCI/PNP & Onboard I/O Setup Screen
        • PNP (Plug And Play)
        • Controller Settings
        • Serial Ports
        • Parallel Port
        • UART2 Use Infrared
        • Internal PCI/IDE, IDE PIO
      • Load BIOS Defaults
        • Load BIOS Defaults Screen
      • Load Setup Defaults
        • Load Setup Defaults Screen
      • Setting Supervisor & User Passwords
        • Password Setting
      • IDE HDD Auto Detection
        • IDE HDD Auto Detection Screen
      • Save And Exit Setup
      • Exit Without Saving
  • NCR SCSI BIOS & Drivers
  • Flash Memory Writer Utility
    • The Flash Memory Writer Utility Screen
    • The Advanced Features Screen
• Technical Summary
  • Jumper Setting Summary
    • Level 2 Cache Size; JP6 & JP8
    • PS/2 Mouse Port Selector: JP12
    • Onboard Audio Selector: JP13
      • Enable
      • Enable
      • Disable
      • CPU Internal Clock External Mulitple Selector: JP14& JP15
      • 2.5 X Ext Clk 3 X Ext Clk
      • Voltage Regulator Output Selector: JP19 & JP21
      • 3.45V-3.6V VRE
      • 66MHz Ext. 60MHz Ext. 50MHz Ext.
      • 40MHz Ext.
    • UARTг/IR Selection: JP35 & JP36
    • Enable
    • COM2
    • Enable
    • IR
    • SMC I/O Selector: JP37
    • Enable SMC I/O
    • Disable SMC I/O
      • Level 2 Cache Options
      • Important:
        • L2 Cache Options
      • Socketed SRAM cache options
      • 256KB
      • cache
      • 32K8x8
      • Cache module installation
      • 512KB
      • cache
      • 64K8x8
      • or
      • 1MB
      • cache
      • 128K8x8
  • External Connections
    • SMI Suspend Switch
    • Reset
    • Keylock
    • Speaker
      • I/O Port Connectors
    • Port & Controller Cables
      • Game port & cable
      • Connecting A Power Supply
  • The PCI-SC200 SCSI Interface Card
    • The PCTSC200 SCSI Interface Card
    • Internal SCSI ribbon cable connector
    • External SCSI 2 cable connector
    • Setting Up the PCI-SC200
      • Setting the INT Assignment
      • JPl & 2: Interrupt settings
    • INT A
    • (default)
    • INTB
    • INTO
    • INTD
      • Terminator Settings
      • JP5: Terminator setting
    • Termination
    • Enabled
    • (default)
    • Termination
    • Disabled
    • SCSI ID Numbers
      • Example 1: Only internal or only external devices connected
      • Example 2: Both internal and external devices connected
  • Declaration of Conformity