Operation, Note, Adjustments – Bolens 117-670-300 User Manual
Page 5: A caution, Cutting height, Throttle, Lubrication, Important, Maintenance, Cutting blade
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
OPERATION
2.
MoVe throttle control lever on handle to
position.
'FAST"
NOTE
For
shipping
purposes
your
mower
is
set
with
the
wheels
in
a
low
cutting
height
position.
For
best
results
raise
the
cutting
position
until
it
is
deter
mined
which
height
is
best
for
your
lawn. See adjustments.
1.
Service engine with gas and oil. See engine manual
packed
with
lawn
mower
for
complete
instructions
tor the care and maintenance of engine. READ DI
RECTIONS CAREFULLY.
2.
When ready to start engine, place throttle control
lever in "START" position and start engine in ac
cordance
with
instructions
in
engine
manual.
After
engine starts, move throttle control lever to desired
engine
speed.
The
engine
is
stopped
by
placing
control lever in the "STOP" position.
3.
Be sure that lawn is clear of stones, sticks, wire or
other
objects
which
could
damage
lawn
mower
or
engine. For best results and to insure more even
grass
distribution, do
not
mow when
lawn is ex
cessively wet.
4. Check blade bolts for proper tightness.
ADJUSTMENTS
A
CAUTION
Do not at any time make any adjust
ment to lawn mower without first stop
ping
engine
and
disconnecting
spark
plug wire.
CUTTING HEIGHT
An adjusting plate and thumb lever at each wheel po
sition
provides
cutting
height
adjustment.
Each
adjust
ing plate has five holes. Height of cot will be changed
when the thumb lever is moved from one hole to an
other.
Simply
depress
thumb
lever
towards
wheel
and
move
wheel
and
lever
assemisly
to
desired
position.
All
wheels
must
be
positioned
in
relative
height
of
cut positions.
THROTTLE
If
adjustment
becomes
necessary,
the
throttle
control
wire assembly can be reset as follows:
1.
Loosen, but do not remove, screw securing throttle
control wire assembly at engine.
3.
AAove lever, to which control wire is fastened at
engine,
to
full
open
position
and
retighten
screw
to secure throttle control wire assembly.
LUBRICATION
IMPORTANT
Always
stop
engine
and
disconnect
spark
plug
wire
before
cleaning,
lub
ricating or doing any kind of work on
lawn mower.
Protective Shield — The pivot points on the protective
shield
should
be
lubricated
periodically
with
light
oil
to prevent any rust or binding.
Chute Deflector — The torsion spring and pivot point
should be lubricated periodically with light oil to pre
vent any rust or binding. Deflector must work freely.
Wheels—Wheel
bearings
are
of
self-lubricating
Forti-
flex. They require no lubrication. If your unit is pro
vided
with
optional
ball
bearing
wheels,
lubricate
at
least once a season with light oil.
Throttle
—
Periodically
lubricate
throttle
control
lever
and throttle wire assembly with a few drops of light
oil (SAE No. 10 or 20) for ease of operation.
Engine
—
Follow
engine
manual
structions.
for lubrication in-
Change
oil
after
first
5
hours-^ifoperation
while
en
gine is warm. Thereafter, change oiT^every 25 hours of
operation
while
engine
is
warm.
Engine
may
be
drained
through
oil
filler
opening.
Be
sure
to
replace
drain plug and oil filler cap.
MAINTENANCE
CUTTING BLADE
The blade may easily be removed for grinding or
replacement as follows:
1.
Remove bolt and lock washer holding blade and
blade adapter to engine crankshaft.
2.
Remove
blade
and
blade
adapter
from
engine
crankshaft.
3.
Remove two bolts, lock washers and nuts holding
blade to blade adapter (if necessary).