Dacor 100500 - Manual (Page 6)


Overlay Panel Specifications
(See Illustrations on page 3.)
42-Inch Model 48-Inch Model
BACKER PANEL
(A) Grille Panel
W Width 40 1/4” (1022mm) 46 1/4” (1175mm)
H Height 8 3/4” (222mm) 8 3/4” (222mm)
(B) Freezer Dispenser Panel
W Width 16 1/4” (413mm) 18 1/2” (470mm)
W1 Width 2” (51mm) 2” (51mm)
W2 Width 14 1/2” (368mm) 14 1/2” (368mm)
H Height 69 1/8” (1756mm) 69 1/8” (1756mm)
H1 Height 34 1/16” (865mm) 34 1/16” (865mm)
H2 Height 48 1/8” (1222mm) 48 1/8” (1222mm)
(C) Freezer Non-Dispenser Panel
W Width 16 1/4” (413mm) 18 1/2” (470mm)
H Height 69 1/8” (1756mm) 69 1/8” (1756mm)
(D) Refrigerator Panel
W Width 23 1/2” (597mm) 27 1/4” (692mm)
H Height 69 1/8” (1756mm) 69 1/8” (1756mm)
SPACER PANEL
(A) Grille Panel
W Width 39 1/4” (997mm) 45 1/4” (1149mm)
H Height 7 3/4” (197mm) 7 3/4” (197mm)
(B) Freezer Dispenser Panel
W Width 15 1/4” (387mm) 17 1/2” (445mm)
W1 Width 2” (51mm) 2” (51mm)
W2 Width 14 1/2” (368mm) 14 1/2” (368mm)
H Height 68 1/8” (1730mm) 68 1/8” (1730mm)
H1 Height 34 1/16” (865mm) 34 1/16” (865mm)
H2 Height 48 1/8” (1222mm) 48 1/8” (1222mm)
(C) Freezer Non-Dispenser Panel
W Width 15 1/4” (387mm) 17 1/2” (445mm)
H Height 68 1/8” (1730mm) 68 1/8” (1730mm)
(D) Refrigerator Panel
W Width 22 1/2” (572mm) 26 1/4” (667mm)
H Height 68 1/8” (1730mm) 68 1/8” (1730mm)
FRONT DECORATOR PANEL
(A) Grille Panel
W Width 40 1/4” (1022mm) 46 1/4” (1175mm)
H Height 8 3/4” (222mm) 8 3/4” (222mm)
(B) Freezer Dispenser Panel
W Width 16 7/16” (418mm) 18 3/4” (476mm)
W1 Width 2 1/4” (572mm) 2 1/4” (572mm)
W2 Width 14 1/4” (362mm) 14 1/4” (362mm)
H Height 69 1/4” (1759mm) 69 1/4” (1759mm)
H1 Height 34 5/16” (872mm) 34 5/16” (872mm)
H2 Height 47 13/16” (1214mm) 47 13/16” (1214mm)
(C) Freezer Non-Dispenser Panel
W Width 16 7/16” (418mm) 18 3/4” (476mm)
H Height 69 1/4” (1759mm) 69 1/4” (1759mm)
(D) Refrigerator Panel
W Width 23 3/4” (603mm) 27 1/2” (699mm)
H Height 69 1/4” (1759mm) 69 1/4” (1759mm)
d
esign
s
PeCifiCaTions
Side Panel Specifications
If using side panels
with the Dacor ®
Built-In Refrigerator,
they will need to be
1/4” (6mm) thick.
Side Panel
(Dimensions Typ.)
82 13/16"
(2103mm)
24" (610mm)
Rear Front
2 1/2"
(64mm)
2 7/16"
(62mm)
1 3/8"
(35mm)
3/8" (10mm)
Toe Kick and Hinge Area
NOTES:
◊ Use counter sink screws for attaching the backer panel to
the front panel.
◊ On 42” custom panels watch location of handle mounting
due to under cut of front panel.
◊ For freezer dispenser front panels, remove fountain trim
and tape to the backside of the backer panel. Note recycle
symbol should be visible and located at the bottom.
◊ You may want to remove any additional material on the
backer panel when used in conjunction with a front panel.
Remove 1/32” on thickness and 1/2” wide of material on
the inside surface of the backer panel. This will help ease
assembly of the panel assembly onto the door.
Backer Panel Thickness 1/4” (6mm)
Spacer Panel Thickness 0.100” (2.5mm)
If Raised Panel is Used Overall Front Panel Thickness Not to
Exceed 1 1/4” (318mm)
Spacer Panel
Backer Panel
Front Decorator Panel
3/4" Max.
1/4"
.10 "
Front Decorator Panel
Backer Panel
Spacer Panel
3/4" Max.
1/4"
.10 "