Dream Property Omikron Plus control DM8000 - Manual (Page 2)

Buttons overview
Battery
IR-Sensor
DREAM-
Control
TV-Control
OK-Button
Numeric
Keypad
EXIT
VOL BOUQUET
2 abc 1 3 def
5 jkl 4 ghi 6 mno
8 tuv
0
7 pqrs 9 wxyz
< <
TV R
PVR
EXIT
INFO
HELP
VOL BOUQUET
2 abc 1 3 def
5 jkl 4 ghi 6 mno
8 tuv
0
7 pqrs 9 wxyz
< <
TV R
MENU
REC TEXT RADIO TV
TV R
PVR
INFO
HELP
TV R
MENU
Inserting the batteries
Before you can start using your Dreambox
remote control you have to insert the 3 AAA
batteries that were supplied with the device.
1. Open the battery compartment at the
back of the remote.
2. Insert the 3 AAA batteries keeping the
polarity (+ and -) in mind.
3. Close the battery compartment and make
sure it is latched completely.
PROGRAMMING USING A CODE
In this way of programming a manufacturer-
specific code is used. (See codelist at
www.dreambox.de)
1. Press the OK-Button and the TV-Control-
Button for approx. 3 seconds, until the
TV-Control-Button lights up red and the blue
illumination of the keys is active.
2. Enter the desired 3-digit code 000~155
using the Numeric Keypad.
(The most recent codelist can be found
online at www.dreambox.de!)
If you cannot control your TV using a code,
please try the next one. You can write down
the code in the field on the right-hand side.
Please try another programming way
described in PROGRAMMING USING THE SEARCH
MODE if none of the supplied codes leads to
success.
TV manufacturer Code
Please note:
• The programming will be aborted if
you don't complete step 2. within 3 seconds.
TV R
PVR
INFO
HELP
TV R
MENU
PROGRAMMING USING THE SEARCH MODE
In this way of programming your Dream-
box remote control will send a different
shutdown signal to your TV every second
until it is turned off. Please use this mode of
programming if no code was successful or
your TV set manufacturer is not inclu-
ded in the list.
1. Press the OK-Button and the TV-Control-
Button for approx. 3 seconds, until the
TV-Control-Button lights up red and the blue
illumination of the keys is active.
2. Enter 777 using the Numeric Keypad to
start the search mode. During the process
point the IR-Sensor in the direction of your
TV.
The blue illumination of the keys is active
and the TV-Control-Button will blink every
time a shutdown signal is being send.
3. Once your TV turns off (Note: Depending
on your TV this may take a few minutes)
press the OK-Button right away to save the
current code and to exit the search mode.
The TV-Control-Button will stop blinking and
the programming has successfully finished.
To exit the search mode without saving the
result simply press the TV-Control-Button.
Please note:
• The programming will be aborted if
you don't complete step 2 within 3 seconds.
• Pressing the TV-Control-Button at any time
will exit the programming mode.
2 abc 1 3 def
5 jkl 4 ghi 6 mno
8 tuv
0
7 pqrs 9 wxyz
< <
2 abc 1 3 def
5 jkl 4 ghi 6 mno
8 tuv
0
7 pqrs 9 wxyz
< <
02/03 DREAMBOX REMOTE CONTROL | DREAM MULTIMEDIA GMBH | PIERBUSCH 24-26 | 44536 LÜNEN | GERMANY
HOTLINE +49 (0) 180 . 3 44 11 30 990 (0,09 €/Min.)