Hatteland Display 19 inch - JH 19T14 MMC - Manual (Page 6)

6
Serial Communication (SCOM) Interface
Communication Interface
IND100084-11
80
IND100241-9
Appendix 81
IND100241-9
Appendix
Pin Assignments - Common Connectors
Note: Not all connectors may be available on your specifi c product. This depends on the amount of additional hardware installed from factory,
or customized solutions. These pin assignments are for the common connectors used. Connectors are seen from users Point Of View (POV).
Pin Assignments - 15P HD RGB VGA
Pin 01 Red, analog
Pin 02 Green, analog
Pin 03 Blue, analog
Pin 04 Reserved for monitor ID bit 2 (grounded)
Pin 05 Digital ground
Pin 06 Analog ground red
Pin 07 Analog ground green
Pin 08 Analog ground blue
Pin 09 +5V power supply for DDC (optional)
Pin 10 Digital ground
Pin 11 Reserved for monitor ID bit 0 (grounded)
Pin 12 DDC serial data
Pin 13 Horizontal sync or composite sync, input
Pin 14 Vertical sync, input
Pin 15 DDC serial clock
5 4 3 2 1
15 14 13 12 11
10 9 8 7 6
Pin Assignments - 24P DVI-I
Pin 01 T.M.D.S. Data2 - (Digital - RED link 1)
Pin 02 T.M.D.S. Data2 + (Digital + RED link 1)
Pin 03 T.M.D.S. Data2/4 Shield
Pin 04 T.M.D.S. Data4 - (Digital - GREEN link 2)
Pin 05 T.M.D.S. Data4 + (Digital + GREEN link 2)
Pin 06 DDC Clock
Pin 07 DDC Data
Pin 08 Analog Vertical Sync (DVI-I only)
Pin 09 T.M.D.S. Data1 - (Digital - GREEN link 1)
Pin 10 T.M.D.S. Data1 + (Digital + GREEN link 1)
Pin 11 T.M.D.S. Data1/3 Shield
Pin 12 T.M.D.S. Data3 - (Digital - BLUE link 2)
Pin 13 T.M.D.S. Data3 + (Digital + BLUE link 2)
Pin 14 +5V Power (for standby mode)
Pin 15 Ground (for +5V and analog sync)
Pin 16 Hot Plug Detect
Pin 17 T.M.D.S. Data0 - (Digital - BLUE link 1) and digital sync.
Pin 18 T.M.D.S. Data0 + (Digital + BLUE link 1) and digital sync.
Pin 19 T.M.D.S. Data0/5 Shield
Pin 20 T.M.D.S. Data5 - (Digital - RED link 2)
Pin 21 T.M.D.S. Data5 + (Digital - RED link 2)
Pin 22 T.M.D.S. Clock Shield
Pin 23 T.M.D.S. Clock + (Digital clock + (Links 1 and 2)
Pin 24 T.M.D.S. Clock - (Digital clock - (Links 1 and 2)
Pin C1 Analog RED
Pin C2 Analog GREEN
Pin C3 Analog BLUE
Pin C4 Analog Horizontal Sync.
Pin C5 Analog Ground (return for RGB signals)
DDC = Display Data Channel /// T.M.D.S = Transition Minimized Differential Signal /// PIN C1,C2,C3,C4 = Only present on DVI-I connectors.
NOTE: Connector shows a DUAL LINK design, but some units may not support it. Only products with 1920x1200 or more in resolution
require / support DUAL LINK.
1 2 3 4 5 6 7 8 C1 C2
9 10 11 12 13 14 15 16 C5
17 18 19 20 21 22 23 24 C3 C4
Pin Assignments - USB TYPE B
Pin 2: Negative Data
Pin 3: Positive Data Pin 4: Ground
Pin 1: VCC +5V
Pin Assignments - Multifunction Cable Outputs
Pin Assignments - 9P Serial COM RS232
Pin 01 - CTRL(+) Buzzer Control (+) (+12V input for driving the buzzer)
Pin 02 - TX Transmit Data
Pin 03 - RX Receive Data
Pin 04 - DTR Data Terminal Ready
Pin 05 - GND Ground
Pin 06 - DSR Data Set Ready
Pin 07 - RTS Request To Send
Pin 08 - CTS Clear To Send
Pin 09 - CTRL (-) Buzzer Control (-) (Pull low to activate buzzer)
5 4 3 2 1
9 8 7 6
Pin Assignments - 5P S-VHS/S-VIDEO
Pin 1: Ground (Y)
Pin 3: Y - Intensity (luminance)
Pin 2: Ground (C)
Pin 4: C - Color (chrominance)
Pin Assignments - RCA & BNC 1P COMP. VIDEO
Ground Shield Pin 1: Video Signal
Connectors that are commonly available on the Multifunction Cable or customized cable.
Connectors are seen from users Point Of View (POV).
Pinout Assignments
For Display Units (MMD/STD w/Multifunction Cable - RS-232).
Pin RS-422 / RS-485, 4-wire - Full Duplex RS-422 / RS-485, 2-wire - Half Duplex
1 N/C N/C
2 RxD- (Receive Data Negative) N/C
3 TxD+ (Transmit Data Positive) TxD+ (Transmit Data Positive)
4 N/C N/C
5 GND (Ground) GND (Ground)
6 N/C N/C
7 RxD+ (Receive Data Positive) N/C
8 TxD- (Transmit Data Negative) TxD- (Transmit Data Negative)
9 N/C N/C
NOTE: N/C (Not Connected) pins may be internally connected. Do not connect these without consulting Hatteland Display.
Pinout Assignments
Display Units (MMD/STD w/Multifunction Cable - RS-422 / RS-485, 4-wire and 2-wire).