Kent UZ 964 Hip Va - Manual (Page 8)

8
4. Wand assembly
a) To connect the wand sections together, simply insert one
section into the other, giving the two assembled sections
a firm push.
b) Adjust the length of the telescopic wand by pressing its
button and altering the wand length. When vacuuming
stairs it is recommended to that the wand is adjusted to its
shortest length.
5. Tools
The accessories shown in the pictures may vary from model
to model.
a) Floor nozzle, one way for brush (hard floor) or smooth for
carpet.
b) Universal nozzle for both hard floors and carpets
c) Combi Brush / Nozzle useful tool for the cleaning of
upholstery, stair carpets, curtains etc.
d) Crevice Tool designed for cleaning in narrow spaces like
furniture, radiators, corners and joints.
e) Paddle Nozzle designed for cleaning beneath furnitures
and wide area cleaning
6. Power supply
For electrical power head. Only on some variants.
7. Accessory loops
The belt is equipped with loops to conveniently hold the
vacuum's accessories. In addition, the power cord can be
held in place on the belt by snapping the nylon loop around
it. Wind up the cord starting at the machine.
8. Start Stop
Convenient finger-tip on / off button
9. Suction control lever
10. Exhaust filter
The exhaust cover is easily removed for filter changes
a) Grasp the cover in your hand.
b) Release the locking mechanism by gently pressing down
on one end of the locking bar.
c) Ease the upper corner away from the vacuum housing.
d) Slide the bottom edge of the cover away so the hinges on
the bottom edge of the cover slip out of the housing.
e) Remove filter holder and used filter.
f) Install new filter and secure with the filter holder.
g) Reinstall exhaust cover as in "Dust Bag installation"
11. Warning
Do not use the vacuum cleaner to pick up water. Wet
surfaces can expose the operator to possible electrical
shock.
1. Dust bag installation
a) Open the triangular shaped dust bag cover by gently
pressing one end of the locking bar to release the locking
mechanism.
b) Grasp the cover in your hand, lifting the upper corners of
the cover away from the vacuum housing.
c) Slide the bottom edge of the cover away so the hinges on
the cover slip out of the housing.
d) Inside the dust bag cavity a round foam filter helps to
protect the motor. Be sure this filter is in place prior to
installation of the dust bag.
e) Always use a Hepa-filter when picking up hazardousma
terial . Remove the standard motor filter if fitted, then fit the
Hepa-filter and turn to lock it in place. Then install the
dustbag.
f) Gently unfold the new dust bag. The upper corner of the
dust bag should be slided in so they do not interfere with
the cardboard plate resting securely on the housing.
g) Ease the dust bag into the cavity, placing the cardboard
plate onto the exterior lip of the cavity, make sure that the
cardboard plate is fitted behind the two small clips on the
exterior lip.
NOTE: The triangular shaped cardboard plate must be
placed evenly on the exterior housing lips in order for the dust
bag cover to be properly installed.
h) Replace the dust bag/hose inlet cover. First grasp the
cover in your hand, and insert the lower cover hinges into
the indentations. Be sure the dust bag cardboard plate is
resting evenly on the lips of the cavity. Close the cover,
and make certain it clicks into place.
2. Belt
The belt locking clip is designed to hold the "hip vac" securely
around your waist while working.
To connect: Simply insert the toothed connector into the belt
buckle until it snaps into place.
To disconnect the belt when work is finished, gently squeeze
the outer clips together, and pull connector out of belt buckle.
To adjust the belt for individual comfort:
Larger: Hold the belt locking clip in one hand and slide the
nylon belt until a loop is formed. Pull the belt locking clip to
adjust the slack in the nylon belt.
Smaller: Pull the loose end of the nylonbelt until adjusted to
desired size.
Soft Belt
2b) Wrap the belt around your waist. Adjust it to the desired
size, by fitting the two nylon parts together.
2c) Then you´ll insert the toothed connector into the belt
buckle until it snaps into place. To disconnect the belt when
work is finished, gently squeeze the outer clips together, and
pull connector out of belt buckle.
3. Hose connection
Fit the hook on the hose adapter in the recess in the hose
opening on the machine. Press and turn about one half-turn
to ensure a secure fit.