LINK Systems Omni II Automatic Setups Module - Manual (Page 3)

October 16, 2008 Manual Version 1.1
i
TABLE OF CONTENTS
Section 1 Introduction.................................................................................................................. 1-1
Section 1.1 Counterbalance Control ............................................................................... 1-1
Section 1.2 Cushion Control ........................................................................................... 1-2
Section 1.3 Shut Height Control ..................................................................................... 1-2
Section 2 Parameter Entry and Access Control ........................................................................... 2-1
Section 2.1 Parameter Entry ........................................................................................... 2-1
Section 2.1.1 Numeric Entries .......................................................................................... 2-1
Section 2.1.2 Text Entry ................................................................................................... 2-1
Section 2.2 Access Control ............................................................................................. 2-3
Section 2.2.1 Key Only Mode........................................................................................... 2-3
Section 2.2.2 Key or Password Mode............................................................................... 2-3
Section 2.2.3 Password Only Mode.................................................................................. 2-4
Section 2.2.4 Key and Password Mode ............................................................................ 2-4
Section 2.2.5 Restricted Items .......................................................................................... 2-4
Section 2.2.6 Access Control Operation ........................................................................... 2-5
Section 2.2.6.1 RUN/PROG Key Switch Operation..................................................... 2-5
Section 2.2.6.2 Password System Operation ................................................................ 2-5
Section 3 Installation.................................................................................................................... 3-1
Section 3.1 Auto-Setup Module Installation................................................................... 3-1
Section 3.1.1 Module Assembly ....................................................................................... 3-2
Section 3.1.2 Assigning Module Number......................................................................... 3-2
Section 3.1.3 Module Mounting ....................................................................................... 3-3
Section 3.1.4 Module Wiring............................................................................................ 3-3
Section 3.1.4.1 Wiring Input Power.............................................................................. 3-4
Section 3.1.4.2 Wiring High Speed Serial Bus Cable................................................... 3-4
Section 3.1.4.3 Setting High Speed Serial Bus Termination Switch ............................ 3-5
Section 3.2 Valve Systems.............................................................................................. 3-5
Section 3.3 Counterbalance Control Installation ............................................................ 3-7
Section 3.3.1 Counterbalance Pressure Transducer Mounting ......................................... 3-9
Section 3.3.2 Counterbalance Air Valve System Mounting ........................................... 3-10
Section 3.3.3 Counterbalance System Wiring ................................................................ 3-10
Section 3.4 Cushion System Installation ...................................................................... 3-10
Section 3.4.1 Cushion Pressure Transducer Mounting................................................... 3-11
Section 3.4.2 Cushion Air Valve System Mounting....................................................... 3-12
Section 3.4.3 Cushion System Wiring ............................................................................ 3-12
Section 3.5 Slide Adjust System Installation................................................................ 3-12
Section 3.5.1 Rotary Transducer Mounting.................................................................... 3-13
Section 3.5.2 Rotary Slide Adjust Wiring ...................................................................... 3-13
Section 4 Configuration ............................................................................................................... 4-1
Section 4.1 Configuring the OmniLink II for the Auto-Setup Module .......................... 4-1
Section 4.2 Configuring the Automatic Setup module ................................................... 4-4
Section 4.2.1 Configuring Air Systems ............................................................................ 4-5
Section 4.2.1.1 Configuring Counterbalance Systems.................................................. 4-6
Section 4.2.1.2 Configuring Cushion Systems ............................................................. 4-8
Section 4.2.2 Configuring Slide Adjust Modules ........................................................... 4-10
Section 4.2.2.1 Configuring a Rotary Slide Adjust System........................................ 4-10