Mighty Mule FM138 - Manual (Page 3)

GTO Exit Wand Instructions 12.28.11 3
4.
Connect the BLACK to the terminal labeled COMMON, and
the BLUE wire to terminal in STEP 3 to open gate.
5.
Connect the POWER INPUT wires to power source.
• Connect the YELLOW and
BRAIDED GROUND wires
to the (–) NEGATIVE side of
power source. (i.e. battery)
• Connect the RED wire to the
(+) POSITIVE side of power
source. (i.e. battery)
6.
Turn opener ON and TEST.
TURN GATE OPENER OFF
ON
ALARM ACCESSORY RCVR
SEQ1
SEQ2 LEARN
BLU ORG WHT GRN R B G
Connect the BLUE wire from
the SENSOR CABLE to the
BLU terminal on the opener
control board.
Connect the Black
wire from the SENSOR
CABLE to one of the
COMMON terminals on the
opener control board.
BLUE
BLACK
RECR
GRN BLK RED EXIT
SAFETY
EDGE CY
CLE
COMMON
LINK
Connect the BLUE wire from
the SENSOR CABLE to the
EXIT terminal on the opener
control board.
Connect the BLACK wire from the
SENSOR CABLE to one of the
COMMON terminals on the
opener control board.
BLUE
BLACK
RECEIVER
ALM
GTO RCVR.
CO
M
GRN BLK RED
CY
CLE
SAFET
Y
EXIT
SHADO
W
OPEN EDGE CO
M
CONTROL INPUTS
CL
OSE EDGE
Connect the BLUE wire from the
SENSOR CABLE to the EXIT
terminal on the opener control
board.
Connect the BLACK wire from
the SENSOR CABLE to one
of the COMMON terminals on
the opener control board.
BLUE
BLACK
COM COM COM G
TO Inc.
SX4000 L
CY
CLE
SAFETY OPEN EDGE
RUN 2 OPEN CL
OSE STOP COM COM COM SHADOW LOOP
Connect the BLUE wire
from the SENSOR CABLE
to the OPEN terminal on
the opener control board.
Connect the BLACK wire from
the SENSOR CABLE to one
of the COMMON terminals on
the opener control board.
BLUE
BLACK
WIRING DIAGRAM EXAMPLES
NOTE: Power Input Connections Not Shown.
(See gate instruction manual for complete instructions)
BRAIDED GROUND
from SENSOR Cable
YELLOW wire from
SENSOR CABLE
RED wire from SENSOR Cable
Battery Cable
BLACK (-)
BLACK BATTERY CONNECTION WIRE
with Spade Connector included with SENSOR
RED BATTERY CONNECTION WIRE
with Spade Connector included with SENSOR
Double Spade Connectors
included with SENSOR
Battery Cable
RED (+)
IMPORTANT
WHEN THE WAND IS FIRST POWERED UP IT
MUST BE UNDISTURBED FOR 60 SECONDS TO
PERFORM THE SELF TEST AND CALIBRATIONS.
BEFORE POWERING THE WAND MAKE SURE
THERE ARE NO MOVING METAL OBJECTS OR
MOVING VEHICLES WITHIN THE RANGE OF
THE WAND
VAR5
K1
PF1
K2
BA
T T +
K3 K4
VAR4 VAR3 VAR2 VAR1
PW
R.
SF
TY
.
EXIT
CY
CLE EDGE
SENSOR COMMON
LOCK+ LOCK–
WHT GRN RED BLK WHT GRN
SECOND OPR. FIRST OPR.
RED BLK
14 V
AC
OR
SOLAR
Connect the BLUE wire from
the SENSOR CABLE to the
EXIT terminal on the opener
control board.
Connect the Black
wire from the SENSOR
CABLE to one of the
COMMON terminals on the
opener control board.
BLUE
BLACK
Connect the BLUE wire from
the SENSOR CABLE to the
EXIT terminal on the opener
control board.
Connect the Black
wire from the SENSOR
CABLE to one of the
COMMON terminals on the
opener control board.
BLACK
POWER
CHGR CHGR EDGE CY
CLE EXIT
SAFETY
COM COM
LOCK+ LOCK -
BLUE