Mossberg 715T - Manual (Page 19)

Using the operating handle, push the bolt fully rearward. While holding the bolt
fully rearward, place the trigger housing assembly into the receiver (Fig. 20).
Allow the bolt to SLOWLY come fully forward. Align the holes in the trigger hous-
ing with the holes in the receiver, and insert the two trigger housing retaing pins
(Fig. 12).
MODELS WITH 702 PLINKSTER STOCK: Place the action into the stock and
reinstall the two take-down screws located in the stock (one to the rear of the trig-
ger guard and one in front of the magazine).
MODELS WITH AR STYLE STOCK: For models with AR style stocks, reverse the
procedure outlined in the “Disassembly for Cleaning and Lubrication” section of
this manual. Ensure that the sling swivel is in place on the barrel prior to reassem-
bly. Tighten the Plastite TM screws until snug. Do not over-tighten the Plastite TM
screws as this can damage the forend and/or receiver shells. Ensure that the front
and rear takedown screws (Fig. 10) are securely tightened.
Check to ensure the firearm is functioning properly, see “Function
Testing” before using live ammunition.
FUNCTION TESTING
AFTER PERFORMING ANY WORK ON YOUR FIREARM SUCH AS
CLEANING, DISASSEMBLY OR INSTALLATION OF AN ACCESSORY:
a. Keep the muzzle pointed in a safe direction, remove the magazine
and pull the operating handle fully rearward to open the action, and
visually and physically check the chamber and inside the receiver to
be certain the firearm is unloaded.
b. Move the safety button fully to the right to the “ON” (SAFE) position.
KEEP THE MUZZLE POINTED IN A SAFE DIRECTION AT ALL TIMES
THROUGHOUT THE FOLLOWING STEPS! FAILURE TO DO SO
COULD RESULT IN SERIOUS INJURY OR DEATH IF THE FIREARM
HAS NOT BEEN PROPERLY UNLOADED, AND FIRES WHILE YOU
ARE TESTING ITS FUNCTION!
Close the action and leave the safety in the “ON” (SAFE) position. Pull the trigger
rearward fully. The hammer should not fall (No Fire).
19
Fig. 20
Using the operating handle, push the bolt fully rearward. While holding the bolt
fully rearward, place the trigger housing assembly into the receiver (Fig. 20).
Allow the bolt to SLOWLY come fully forward. Align the holes in the trigger hous-
ing with the holes in the receiver, and insert the two trigger housing retaing pins
(Fig. 12).
MODELS WITH 702 PLINKSTER STOCK: Place the action into the stock and
reinstall the two take-down screws located in the stock (one to the rear of the trig-
ger guard and one in front of the magazine).
MODELS WITH AR STYLE STOCK: For models with AR style stocks, reverse the
procedure outlined in the “Disassembly for Cleaning and Lubrication” section of
this manual. Ensure that the sling swivel is in place on the barrel prior to reassem-
bly. Tighten the Plastite TM screws until snug. Do not over-tighten the Plastite TM
screws as this can damage the forend and/or receiver shells. Ensure that the front
and rear takedown screws (Fig. 10) are securely tightened.
Check to ensure the firearm is functioning properly, see “Function
Testing” before using live ammunition.
FUNCTION TESTING
AFTER PERFORMING ANY WORK ON YOUR FIREARM SUCH AS
CLEANING, DISASSEMBLY OR INSTALLATION OF AN ACCESSORY:
a. Keep the muzzle pointed in a safe direction, remove the magazine
and pull the operating handle fully rearward to open the action, and
visually and physically check the chamber and inside the receiver to
be certain the firearm is unloaded.
b. Move the safety button fully to the right to the “ON” (SAFE) position.
KEEP THE MUZZLE POINTED IN A SAFE DIRECTION AT ALL TIMES
THROUGHOUT THE FOLLOWING STEPS! FAILURE TO DO SO
COULD RESULT IN SERIOUS INJURY OR DEATH IF THE FIREARM
HAS NOT BEEN PROPERLY UNLOADED, AND FIRES WHILE YOU
ARE TESTING ITS FUNCTION!
Close the action and leave the safety in the “ON” (SAFE) position. Pull the trigger
rearward fully. The hammer should not fall (No Fire).
19
Fig. 20
135055_PN 17925 Rev E.indd 19 1/4/13 9:57 AM