Peg-Perego Skate System - Manual (Page 21)

- 21 -
Skate BASSINET UNIT
• It must be attached to the Skate chassis
facing the person pushing and in a horizontal
position.
• It can be set at 3 different heights.
• It cannot be used in motor vehicles, but it is
possible to use it on the Peg Perego Skate stand.
Skate SEAT
• It can be attached to the Skate chassis facing
the person pushing or facing forwards.
• It can be set at 3 different heights and
reclining positions.
• It cannot be used without the Skate chassis.
ITEM COMPONENTS
• Check the contents of the packaging. For any
complaints, please contact Customer.
• Skate chassis with basket
• Skate bassinet unit
• Skate seat
• 4 wheels with shock absorbers and ball
bearings (2 swivel or locking front wheels – 2
non-swivel rear wheels)
• More capacious basket
• Drink holder
• Front bar
• Hood
• Cover
• Rain canopy
• Set of standard adaptors for a Peg Perego
Group 0+ car seat.
INSTRUCTIONS FOR USE
SKATE CHASSIS
1• FITTING THE WHEELS: Remove the protective
caps from the rear wheels. To fit the rear
wheels, push the pins into their housing until
you hear them click into place (Fig.a).
Before fitting the front wheels, make sure
that the indicators on the attachment knobs
are red. Insert the wheel pins into their
housing, making sure the green lines on the
wheels match up with the green lines on the
housing. Lastly, turn the attachment knobs
until the indicators are green (Fig.b).
IMPORTANT: Pull on the wheels to make
sure they are correctly attached.
2• OPENING: If it is completely lowered, raise the
handle to prevent it impeding the movement
of the central closure pedal: open the two
levers outwards and move the handle. Move
the two levers back into position (Fig.a).
To open the Skate chassis, release the closure
lever from the right pin of the chassis while
slightly lifting the chassis (Fig.b).
3• Hold the Skate chassis still with a foot on the
rear ledge and lift the handle until it clicks
into place (Fig.a).
Ensure the frame opens correctly by checking
that the green line on the rear footrest is
visible (see figure). If this is not visible, pull
the central handle upwards forcefully.
CENTRAL BRAKE: To set the brake on the
stroller, lower the levers on the rear wheels
with your foot (Fig.b).
To release the brakes, lift the levers.
4• HANDLE: It can be set at various heights. To
adjust the height of the handle, open the two
levers outwards, position the handle at the
desired height and close the two levers (Fig.a).
DRINK HOLDER: It can be fitted on both sides
of the Skate chassis. To fit it, slide the back of
the drink holder into the clips on the Skate
chassis (Fig.b).
5• BASKET: It has adjustable elastic straps for
securing items. Before securing the straps,
put them in the required position (Fig.a).
It is possible to fit, more capacious basket
which is provided (Fig.b).
6• FRONT SWIVEL WHEELS: To put the front
wheels in swivel mode, lift the stopper up
(Fig.a). To turn off swivel mode, press the
stopper down (Fig.b).
Turn the wheels around once to lock them
automatically.
7• REMOVING THE WHEELS: To remove the rear
wheels from the Skate chassis, pull the pin and
at the same time pull off the wheels (Fig.a).
To remove the front wheels from the Skate
chassis, turn the attachment knobs until the
indicators are red, then pull off the wheels
(Fig.b).
SKATE BASSINET UNIT
8• ASSEMBLING THE STRUCTURE: Lift the internal
padding (Fig.a) and the backrest (Fig.b).
9• Attach the tab to the head end of the Skate
bassinet unit (Fig c).
Caution: the central internal belt must be
placed between the tab and the backrest,
as in the figure.
Put the backrest in the lowest position (Fig.d).
10•Turn and attach the two side tabs (Fig.a) and
then the one at the feet end (Fig.b) on the
bottom of the inside of the Skate bassinet unit.
11•Fold the padding back inside (Fig.a).
Lift the backrest and fit the mattress pad in
place (Fig.b).
12•ATTACHING the Skate bassinet unit to the
Skate chassis: Before attaching the Skate
bassinet unit, check that the attachments
on the Skate chassis are both in the same
position. They are correctly positioned when
the graphic symbols on the attachment
points are in line with the ones on the Skate
chassis (Fig.a).
To attach the Skate bassinet unit, position
its couplings in their housing on the Skate
chassis and click them into place (Fig.b).