Peg-Perego Skate System - Manual (Page 24)

- 24 -
Lift the side tabs (Fig. b) to aid the procedure.
Next lift the backrest to release the tab at the
head end (Fig. c).
36•Lower the entire structure and the padding of
the Skate bassinet unit (Fig.a).
Remove the casing sections on both sides,
lifting them outwards from the inside (Fig.b).
37•Slip off the fabric covering in the order shown
in the figure, starting from the side of the
backrest (first from one corner, then from the
other) to aid the procedure (Fig.c).
Finally, slip the fabric covering off the feet on
the bottom of the Skate seat (Fig.d).
How to replace the covers of
the SKATE BASSINET UNIT
PLEASE NOTE: The head end of the Skate
fabric covering can be identified by the slot in
the material for the backrest adjuster strap.
38•Fit the padding, attaching it to the feet on
the bottom of the Skate bassinet unit, then
the side of the feet (one corner at a time) and
next the side fasteners, making quite sure
that they remain on the outside (Fig.a).
Fit the fabric covering on the upper part
(backrest side) one corner at a time.
Lift the backrest and thread the backrest
adjuster strap from the inside to the outside
of the Skate bassinet unit (Fig.b).
Follow the instructions in points 9, 10 and 11.
Put the two casing sections in place (Fig.c).
How to remove the covers of
the SKATE SEAT
Remove the hood, cover and front bar if they
are attached.
39• Open the two Velcro fastenings placed under
the footrest and pull out the straps (Fig. a).
Unfasten the side buttons (Fig. b).
Slide the fabric covering out from inside the
casing sections (Fig. c).
Unfasten the buttons on the side of the
chassis (Fig. d).
40•Pull the leg divider strap of the harness out
from under the seat.
Release the belt behind the backrest and
then pull out the safety harness straps from
the front (Fig. a).
Use a crosshead screwdriver to unscrew the
strap from the Skate seat on one side only,
keeping a finger under the nut (Fig. b).
41•Remove the fabric covering from the backrest
adjustment lever and pull the fabric covering
off upwards near the backrest.
Uncovered frame.
How to replace the covers of the SKATE SEAT
42•Fit the fabric covering onto the frame from
the upper part of the backrest (Fig. a),
keeping the handle on the outside.
• Thread the lower leg divider strap through
under the seat, leaving the higher leg divider
strap above the fabric covering (Fig. b).
• Insert the waist strap into the hole on the
Skate seat (Fig. c) and secure the strap with a
crosshead screwdriver (Fig. d).
43•Put the safety harness at the required height
(Fig. a) by threading the straps through the
slots in the fabric covering.
PLEASE NOTE: Place the buckles underneath
the support straps behind the backrest (Fig. b).
44•Fit the fabric covering onto the casing
sections, first on the upper part and then
on the lower part, slightly lifting the casing
sections to attach it properly (Fig. a).
• Fasten the fabric covering’s two buttons to the
frame, ensuring that the Skate’s side attachments
remain on the outside (Fig.b).
Fasten the straps and stick the Velcro fastenings
to the footrest (Fig. c).
SERIAL NUMBERS
45•The following information can be found on the
Skate chassis (Fig. a), Skate bassinet unit (Fig. b)
and Skate seat (Fig. c): product name, production
date and serial number. This information is
required in the event of a complaint.
ACCESSORIES LINE
46•Skate Parasol: Practical matching parasol.
CLEANING AND MAINTENANCE
• This item requires a small amount of cleaning.
Cleaning and maintenance must only be
carried out by adults.
• Keep all moving parts clean and if necessary
lubricate them with light oil, in line with the
instructions given in point 47.
• Dry the metal parts of the product to prevent rust.
• Clean the plastic parts periodically with a
damp cloth. Do not use solvents or similar
substances.
• Protect this item from the elements: water,
rain and snow. Continual, extended exposure
to the sun may cause colour changes in many
materials.
• Store this item in a dry place.
47•A - Keep clean and free of dust and stones.
B - Keep clean and free of dust and stones.
Periodically lubricate in the point shown.
C - Keep clean and free of dust and stones.
DO NOT lubricate.
• For the upkeep of the fabric parts: brush
them to remove dust and hand wash them
at a maximum temperature of 30°C; do not
wring; do not use chlorine bleach; do not
iron; do not dry clean; do not apply solvent-