SkyRC Toro TS50 Sensored ESC - Manual (Page 2)

Black power wire
(battery negative)
Red power wire
(battery positive)
Battery
Pack
WARRANTY AND SERVICE
The TORO TS50 50A ESC is guaranteed to be free from defects in materials or
workmanship for a period of 90 DAYS from the original date of purchase (verified by dated,
itemized sales receipt). Warranty does not cover incorrect installation, components worn by
use, damage to case or exposed circuit boards, damage due to timing, damage from using
more than 2 LiPo cells input voltage, cross-connection of battery/motor power wires,
overheating solder tabs, reverse voltage application, improper use or installation of external
BEC, damage resulting from thermal overload or short-circuiting motor, damage from
incorrect installation of FET servo or receiver battery pack, tampering with internal
electronics, allowing water, moisture, or any other foreign material to enter ESC or get onto
the PC board, incorrect installation/wiring of input plug plastic, allowing exposed wiring or
solder tabs to short-circuit, or any damage caused by a crash, flooding or natural disaster.
Because SKYRC has no control over the connection & use of the speed control or other
related electronics, no liability may be assumed nor will be accepted for any damage
resulting from the use of this product. Every SKYRC speed control & motor is thoroughly
tested & cycled before leaving our facility and is, therefore, considered operational. By the
act of connecting/operating speed control, user accepts all resulting liability. In no case shall
our liability exceed the product's original cost. We reserve the right to modify warranty
provisions without notice. This product is not intended for use by children under 14 years of
age without the strict supervision of an adult. Use of this product in an uncontrolled manner
may result in physical damage or injuries take extra care when operating any remote control.
For any repair or replace service, please contact your dealer in the first instance, who is
responsible for processing guarantee claims.
SPECIFICATION
Constant/Burst Current
Motor Compatible
Car Compatible
Motor Limits
Resistance
Battery Cell Count
BEC Output
Size
Weight
FAN
REMARK: All the testing results are working with 540 class motors.
50A/300A
Brushless Sensor & Sensorless ESC
1/10 Buggy and Touring Car
4-6S NiMH or 2S LiPo-- ≥8.5T(1/10 Touring Car), ≥11.5T(1/10 Buggy)
0.0006ohm
4-6S NiMH or 2S LiPo
6V@2A
35.3x32.4x19.7mm (LxWxH)
60g
Optional part
ESC PROGRAMMING
The ESC can be programmed by program box, PC (connected with SKYLINK).
Note: the program box can be used as SKYLINK.
Programmable Items and Description
Note: There is no timing function for TS 50 ESC. Even you can find Boot and Turbo Timing
setting in program box and software.
Program Item
Running Mode
Motor Direction
Reverse Speed
Voltage Cutoff
ESC Overheat Protection
Motor Overheat Protection
Punch Rate Switch Point
1st Stage Punch Rate
2nd Stage Punch Rate
TH Input Curve
Throttle Dead Band
Throttle Status
Drag Brake
Brake Strength
Initial Brake
Brake Rate Switch Point
1st Stage Brake Rate
2nd Stage Brake Rate
Brake Input Curve
Section
General
Setting
Throttle
Control
Brake
Control
Forward/Brake
Normal
25-100% (in 1% increment)
3.0-11V (in 0.1V increment)
85℃/185℉
85℃/185℉
1-99%(in 1% increment)
1-30(in 1 increment)
1-30(in 1 increment)
Linear
0.002-0.150ms
0-100%(in 1% increment)
0-100%(in 1% increment)
=Drag Brake
1-99%(in 1% increment)
1-20(in 1 increment)
1-20(in 1 increment)
Linear
Forward/Brake/Reverse
Reverse
Auto (3.2V)
105℃/221℉
105℃/221℉
Custom
Custom
Description
Forward/Reverse
125℃/257℉
125℃/257℉ Disable
Disable
Profiles Preset
The users could preset and store 10 sets of profiles in the ESC. These data could be called
out for application at any time without any special program setting. The user could also reset
the profile according to his request. There is one factory default setting called Modify in the
ESC. This mode can be used for modify class of touring car racing.
Setting Details of Modify Mode
Program Item
Running Mode
Motor Direction
Reverse Speed
Voltage Cutoff
ESC Overheat Protection
Motor Overheat Protection
Punch Rate Switch Point
1st Stage Punch Rate
2nd Stage Punch Rate
TH Input Curve
Throttle Dead Band
Drag Brake
Brake Strength
Initial Brake
Brake Rate Switch Point
1st Stage Brake Rate
2nd Stage Brake Rate
Brake Input Curve
Section
General
Setting
Throttle
Control
Brake
Control
Description
Forward/Brake
Normal
25%
3.2V/1S (Auto)
105℃/221℉
105℃/221℉
50%
5
5
Linear
0.080ms
10%
75%
=Drag Brake
50%
10
16
Linear
How to program the ESC?
2. PC via SKYLINK
1. Program Box
Black power wire
(battery negative)
Red power wire
(battery positive)
PC
Battery
Pack
Modify Mode Setting Value
8/8 7/8 6/8 5/8
If you set the cut-off voltage manually, please note the adjustable votage is TOTAL cut-off
voltage of the battery pack. In AUTO mode, the default cut-off voltage is 3.2V/S, for
example, the cut-off voltage of a 2S battery pack is 3.2Vx2=6.4V in AUTO mode.
Manufactured by
SKYRC TECHNOLOGY CO., LTD.
www.skyrc.com
14
+Yr
2013 SkyRC Technology Co., Ltd. All Rights Reserved.
Ver 1.0 7504-0423-01