Xblue Networks X-50 - Manual

The X-50 is very flexible and can be installed several different
ways but the best way is to connect the Wide Area Network
(WAN) port of the X-50 and all of your X-2020 telephones to
your existing data network; leaving the Local Area Network (LAN)
port unused.
Installing the X-50 this way will allow the system to synchronize
the time and date from the Internet and if wanted connect low cost
Internet SIP Telephone lines.
Getting Started
Product Support is available at www.xbluenetworks.com or call 866-925-8312
Get the most current documentation from
LAN P
ort
WAN P
ort
Line 6
Pow
er
USB P
ort
Line 5Line 4Line 3Line 2Line 1
Telephone Lines Cor
dless/F
AX
System Components
X-50
8 Port Switch
Telephone
Line Cords
X-2020
24 Button Sidecar
X-50 Components
Component Quantities may vary
Power Supply
Quick Start Guide
Ethernet Cable
Power Supply
Power Supply
Ethernet Cable
1. Plug the X-50 in and allow it to power up without connecting any Telephones.
Powering up
The X-50 will be fully powered up and operational when the power LED stops
flashing.
2. Use an Ethernet cable to connect your Personal Computer, Laptop or Desktop
running Windows XP, Vista or Windows7, to the LAN port of the X-50 System.
3. Open Internet Explorer and enter 192.168.10.1 in the address bar, and press enter.
When prompted enter the user name “admin2583 and password (000000) six zeros.”
4. Select Manual Setup to begin the Setup Wizard and then click “Next”.
7. Use the provided Ethernet cable to connect the X-50 WAN port to your network
router or network switch, depending on your network configuration choice.
authenticate. The first one will be assigned extension 101. Each additional X-2020
telephone will automatically authenticate and be assigned the next available
extension number.
8. Connect your X-2020 telephones, one at a time, allowing each of them to
At Default:
• Extension 101 is the Attendant Extension (dial 0)
• All incoming telephone line calls will ring at all registered extensions
• The buttons labeled 1-4 on the phone are pre-programmed as telephone lines 1-4
6. Attention: To secure your system against unwanted outside intrusion (hacking)
9. Change the Extension Password - The X-50 system allows your X-2020
Telephones to automatically authenticate with your system. The default password
that is used is the extension number twice. i.e. 101101, 102102, etc. You should
change the password on all 24 extensions to a unique 6 to 10 digit password even if
you are not using all of them.
Product Support is available at www.xbluenetworks.com or call 866-925-8312
Default Login and Passwords:
Level/Rights Login Default Password New Password
Administrator admin2583 000000
Administrator support support
User (Limited) user user
we strongly recommend that the first thing you do is change all of the
System’s Passwords! Before you begin programming you should change all
three levels of passwords, admin2583, support and user. A password of up to 16
alphanumeric characters may be used and we recommend that you use at least 10.
The best passwords consist of upper and lower case characters and punctuation.
MAKE SURE TO MAKE A NOTE OF YOUR PASSWORD!
For more information go to downloads at www.xbluenetworks.com/x-50-support.html
To change the password, log in as the Administrator go to:
Management --> Access Control --> Password
BE SURE TO MAKE A NOTE OF YOUR NEW PASSWORDS
A list of additional security steps is available at www.xbluenetworks.com or by request at
[email protected]
5. The Setup Wizard can be helpful but it is not critical. The X-50 will function even if
no changes are made in the Setup Wizard. All changes can be made later so when in
doubt, skip through the Setup Wizard’s questions by scrolling to the bottom of each
page and clicking on “Next”. On the last page click on “Save and reboot”. The X-50
will be back on-line when the power light stops flashing.
www.xbluenetworks.com/x50-support.html