Lenco IPD-3560 - Manual (Page 7)


GB

GB
Sleep Timer Function
Sleep to timer
This feature allows you to fall asleep to the radio or iPod / iPhone for up to 60 Minutes.
The unit shuts off automatically when the time expires.
1. Press the POWER/STANDBY button to turn the unit on.
2. Either tune to the desired radio station in radio mode or playback music from the iPod
/ iPhone.
. To select the sleep timer to turn the unit off after 5, 0, 45 or 60 minutes, press the
SLEEP button repeately. The display show the indicator . The unit plays for the
selected length of time then automatically turns off.
4. To turn the unit off before the sleep timer counts down to zero, press the POWER/
STANDBY button at any time.
Notes :
If you are falling asleep to music from an external device connected to the AUX input,
the sleep timer will shut off the power to this system but it will not turn off the external
device.
Care and Maintenance
- Do not subject the unit to excessive force, shock, dust or extreme temperature.
- Do not tamper the internal components of the unit.
- Clean your unit with a damp (never wet) cloth. Solvent or detergent should never be used.
- Avoid leaving your unit in direct sunlight or in hot, humid or dusty places.
- Keep your unit away from heating appliances and sources of electrical noise such as
fluorescent lamps or motors.
Resetting the Unit
If the unit experiences a power surge or electric shock, it is possible that the internal
micro-controller may lock up and the unit will not respond to any commands from the top
panel controls.
. In this event, unplug and then reconnect the AC power plug into the wall outlet.
2. Use a straightened paper clip, toothpick or similar objects to press the RESET button
located at the rear of the main unit (see the below figure). The reset operation clears
the system memory and all of your previous settings will be erased.
CAUTION: DO NOT USE SHARP, POINTED OBJECT TO PRESS THE RESET
BUTTON. IT MAY DAMAGE THE RESET SWITCH INSIDE THE UNIT.
Alarm Operation
The unit is designed with dual alarm,alarm  and alarm .
To set the alarm/ when the unit is OFF (power off mode):
Select wake up alarm source
1. Press and hold the ALM 1 / 2 button until the alarm source indicator blink.
2. Press the FUNC button to select alarm source BUZ (buzzer) , RAD (radio) or iPod / iPhone.
Setting the alarm time
3. Press the VOL/HR + / - button to set alarm hour.
4. Press the TUN / CH / MIN + / - button to set alarm minute.
Save settings and activate alarm
5. To save all settings and auto-exit the setting mode, wait for a few seconds.
6. To activate the daily alarm, press the ALM  /  button and the corresponding alarm
source indicator appears on the LCD display.
Notes :
--- If "Wake to iPod / iPhone" is selected but your iPod has not been docked, the alarm
source will be redirected to the Alarm Buzzer automatically when the alarm is
reached.
--- When "Wake to Radio" is selected, make sure the radio station which you want to
wake to is tuned.
Wake to Buzzer
When the alarm time is reached, the buzzer alarm will sound for 1 Minute.
It goes into Auto-snooze mode if no further button has been pressed. The display
shows the "SNOOZE" indicator. The buzzer turns off for the snooze time (around 10
minutes) then comes on again. This operation will be repeated three times. After the
fourth alarm is finished, the alarm will shut off until the same alarm time on the next
day.
You may also activate the snooze function manually after the alarm sounds by
pressing the SNOOZE button. The buzzer stops for the snooze time then comes
again.
To cancel the snooze before it expires, press the ALM 1 / 2 button.
The snooze operation (including auto-snooze and manual snooze) can be repeated
by  times only.
To stop the alarm immediately after the buzzer sounds, you can also press the ALM
/  button. It resets itself for the following day.
Wake to iPod / iPhone or Radio
When the alarm time is reached, the selected alarm source (iPod/ iPhone or Radio)
will automatically turn on. It starts softly and gradually becomes louder.
It plays for 60 minutes then shuts off and resets itself for the following day.
During the activation of the alarm source, you may press the SNOOZE button to
activate the snooze function. The alarm stops for the snooze time (around 10
minutes) then turns on again.
To cancel the snooze before it expires, press the ALM 1/2 button.
This manual snooze operation can be repeated three times. Each time the alarm
turns on, it plays for 60 minutes (without pressing the snooze button).
To stop the alarm immediately after the alarm sounds, you may also press the ALM
/ button. It resets itself for the following day. RESET button
IPD3560 4lang.indd 12-13 2011-3-18 11:19:36