Lenco IPT-22 DVD - Manual (Page 3)

4 5
SLEEP FUNCTION
Press SLEEP button at power on mode. Each time SLEEP button is pressed, the display changes
Sleep time in a sequence as follows:
90 80 70 60 50 40 30 20 10 OFF
When the sleep time is expired, the unit will switch off automatically.
iPod/iPhone OPERATING
PLAYING AN iPod/iPhone
1. Dock an iPod/iPhone onto the unit.
2. Press the POWER ON/OFF button on the rear of the unit and press STANDBY button to turn the unit
on.
3. Press the FUNCTION button continuously to toggle the unit to IPOD mode.
4. Press PLAY/PAUSE button to play and pause the docked iPod/iPhone.
5. During normal playback, Press PREVIOUS/NEXT button to skip the tracks ahead or backward.
Press and hold FAST FORWARD or FAST BACKWARD button on the remote to search through the
current track forward or backward at a high speed.
6. Press MENU button on the remote to return back the menu the inserted iPod/iPhone, use navigation
up/down button to select your desired track for playback, confirm your selection by pressing ENTER
button.
7. Use STOP button to cease the iPod/iPhone playback.
NOTE: During playback, the connected iPod/iPhone may skip to another song accidently. Once the
problem occurs, please change the shake from “on” to “off” inside Settings of iPod/iPhone.
FM RADIO
TUNING THE FM RADIO
1. Press the POWER ON/OFF button on the rear of the unit and press STANDBY button to turn the unit
on.
2. Press FUNCTION button to switch the unit to radio mode (the radio frequency shows on the LCD
display).
3. Press PREV/NEXT button on the main unit or TUNE+/- button on the remote to fine tune the radio
station. Press and hold PREV/NEXT button on the unit or TUNE-/+ button on the remote to
automatically tune the radio frequency backward and forward respectively. When the tuning goes to
one available station, broadcasting starts immediately.
4. Press ST/MO button on the remote to switch the radio between FM(MONO) and FM(ST).
5. If the unit broadcast a program with RDS, the RDS icon will be shown on the LCD display. Press
INFO button on the remote to check the frequency of the current station.
SAVING FM RADIO STATIONS TO THE UNIT'S MEMORY
1. After tuning the FM radio to the desired stations, press MEM button, "MEM" is shown on the LCD
display with a flashing number of a memory cell.
2. Press CH+/ CH- button to select the radio memory cell.
3. Press MEM button again to save the current radio station to the selected memory cell.
4. To recall the preset station frequency, press CH+ or CH- button repeatedly.
TONE SETTING FOR THE UNIT
During playback, press TONE button once, and use VOLUME CONTROLLER on the unit to adjust the
bass. Press TONE button twice repeatedly for adjusting treble effect by rotating VOLUME
CONTROLLER on the unit as adjust bass effect. Press the TONE button thrice to resume the previous
display.
The bass and treble effect also can be adjusted by pressing BASS+/- button and TREBLE+/- button on
the remote.
MUTE THE UNIT
During playback, press MUTE button to switch off the audio. Press the button again to resume the
audio.
AUX IN
Your player can be used as a power amplifier to playback the programs from portable radio, TV set or
MP3 player or whatever provided this appliance is so designed that audio signal may be produced
through a LINE-OUT jack or the like.
Observe the following steps to connect the player to another appliance:
1. Connect the appliance into the player's left & right AUX IN jacks with the LINE OUT cables.
2. Press STANDBY button to turn the unit on.
3. Press FUNCTION button repeatedly to switch the unit to AUX mode.
4. Power on the appliance and begin play.
At this time, you will be able to hear the sound produced from the connected appliance.
3D FUNCTION
In case the speaker cut off on the chipset protection, please turn OFF and ON as reset to resume the
3D function.
DVD OPERATIONS
PREPARATION
Power on the TV set and select video input mode.
Power on the audio system which is connected to the player.
GET STARTED
1. Press the POWER on/off button on the rear of the unit and then press STANDBY button to turn on the
player.
2. Press FUNCTION button repeatedly to switch to DISC mode. Press EJECT key to open the disc tray.
3. Place a disc onto the disc tray.
4. Close the disc tray by pressing the EJECT button again and the playback starts automatically.
5. When a menu screen appears on the TV, press the navigation buttons or press the numeric buttons
to select a preferred track number, then press ENTER button on the remote or PLAY/PAUSE button
on the unit to start playback.
ADJUST THE VOLUME
Adjust the volume output by pressing the VOL+/- button on the remote or rotating the VOLUME
CONTROLLER on the unit.
SKIP AHEAD OR BACK
Press PREVIOUS button during play to skip to previous chapter (DVD) or track (CD), Press NEXT
button during play to skip to next chapter (DVD) or track (CD).
RAPID ADVANCE/REVERSE
During playback, press FAST FORWARD/FAST BACKWARD button on the remote continuously to
scan the disc forward or backward at X2, X4, X8, X20 normal speed.
Press PLAY/PAUSE button to resume normal play.
STOP PLAYBACK
Press STOP button during playback to stop playback; the player activates its resume function when
STOP is pressed in STOP mode; press PLAY/PAUSE button again, playback resumes at the point it
stopped previously; open the disc tray or press the STOP button one more time to clear the resume
function.