Document Outline

• Preface
• Table of Contents
• Chapter 1 Introduction
  • 1.1 Receiving and Inspection
    • 1.1.1 Nameplate Information
    • 1.1.2 Model Explanation
    • 1.1.3 Series Number Explanation
    • 1.1.4 Drive Frames and Appearances
    • 1.1.5 Remove Instructions
  • 1.2 Preparation for Installation and Wiring
    • 1.2.1 Ambient Conditions
    • 1.2.2 DC-bus Sharing: Connecting the DC-bus of the AC Motor Drives in Parallel
  • 1.3 Dimensions
  • Chapter 2 Installation and Wiring
    • 2.1 Wiring
    • 2.2 External Wiring
    • 2.3 Main Circuit
      • 2.3.1 Main Circuit Connection
      • 2.3.2 Main Circuit Terminals
    • 2.4 Control Terminals
  • Chapter 3 Keypad and Start Up
    • 3.1 Keypad
    • 3.2 Operation Method
    • 3.3 Trial Run
  • Chapter 4 Parameters
    • 4.1 Summary of Parameter Settings
    • 4.2 Parameter Settings for Applications
    • 4.3 Description of Parameter Settings
    • 4.4 Different Parameters for VFD*E*C Models
  • Chapter 5 Troubleshooting
    • 5.1 Over Current (OC)
    • 5.2 Ground Fault
    • 5.3 Over Voltage (OV)
    • 5.4 Low Voltage (Lv)
    • 5.5 Over Heat (OH)
    • 5.6 Overload
    • 5.7 Keypad Display is Abnormal
    • 5.8 Phase Loss (PHL)
    • 5.9 Motor cannot Run
    • 5.10 Motor Speed cannot be Changed
    • 5.11 Motor Stalls during Acceleration
    • 5.12 The Motor does not Run as Expected
    • 5.13 Electromagnetic/Induction Noise
    • 5.14 Environmental Condition
    • 5.15 Affecting Other Machines
  • Chapter 6 Fault Code Information and Maintenance
    • 6.1 Fault Code Information
      • 6.1.1 Common Problems and Solutions
      • 6.1.2 Reset
    • 6.2 Maintenance and Inspections
  • Appendix A Specifications
  • Appendix B Accessories
    • B.1 All Brake Resistors & Brake Units Used in AC Motor Drives
      • B.1.1 Dimensions and Weights for Brake Resistors
    • B.2 No-fuse Circuit Breaker Chart
    • B.3 Fuse Specification Chart
    • B.4 AC Reactor
      • B.4.1 AC Input Reactor Recommended Value
      • B.4.2 AC Output Reactor Recommended Value
      • B.4.3 Applications
    • B.5 Zero Phase Reactor (RF220X00A)
    • B.6 Remote Controller RC-01
    • B.7 PU06
      • B.7.1 Description of the Digital Keypad VFD-PU06
      • B.7.2 Explanation of Display Message
      • B.7.3 Operation Flow Chart
    • B.8 KPE-LE02
      • B.8.1 Description of the Digital Keypad KPE-LE02
      • B.8.2 How to Operate the Digital Keypad
      • B.8.3 Reference Table for the 7-segment LED Display of the Digital Keypad
    • B.9 Extension Card
      • B.9.1 Relay Card
      • B.9.2 Digital I/O Card
      • B.9.3 Analog I/O Card
      • B.9.4 Communication Card
      • B.9.5 Speed Feedback Card
    • B.10 Fieldbus Modules
      • B.10.1 DeviceNet Communication Module (CME-DN01)
        • B.10.1.1 Panel Appearance and Dimensions
        • B.10.1.2 Wiring and Settings
        • B.10.1.3 Mounting Method
        • B.10.1.4 Power Supply
        • B.10.1.5 LEDs Display
      • B.10.2 LonWorks Communication Module (CME-LW01)
        • B.10.2.1 Introduction
        • B.10.2.2 Dimensions
        • B.10.2.3 Specifications
        • B.10.2.4 Wiring
        • B.10.2.5 LED Indications
      • B.10.3 Profibus Communication Module (CME-PD01)
        • B.10.3.1 Panel Appearance
        • B.10.3.2 Dimensions
        • B.10.3.3 Parameters Settings in VFD-E
        • B.10.3.4 Power Supply
        • B.10.3.5 PROFIBUS Address
      • B.10.4 CME-COP01 (CANopen)
        • B.10.4.1 Product Profile
        • B.10.4.2 Specifications
        • B.10.4.3 Components
        • B.10.4.4 LED Indicator Explanation & Troubleshooting
    • B.11 DIN Rail
      • B.11.1 MKE-DRA
      • B.11.2 MKE-DRB
      • B.11.3 MKE-EP
  • Appendix C How to Select the Right AC Motor Drive
    • C.1 Capacity Formulas
    • C.2 General Precaution
    • C.3 How to Choose a Suitable Motor
  • Appendix D How to Use PLC Function
    • D.1 PLC Overview
      • D.1.1 Introduction
      • D.1.2 Ladder Diagram Editor – WPLSoft
    • D.2 Start-up
      • D.2.1 The Steps for PLC Execution
      • D.2.2 Device Reference Table
      • D.2.3 WPLSoft Installation
      • D.2.4 Program Input
      • D.2.5 Program Download
      • D.2.6 Program Monitor
      • D.2.7 The Limit of PLC
    • D.3 Ladder Diagram
      • D.3.1 Program Scan Chart of the PLC Ladder Diagram
      • D.3.2 Introduction
      • D.3.3 The Edition of PLC Ladder Diagram
      • D.3.4 The Example for Designing Basic Program
    • D.4 PLC Devices
      • D.4.1 Summary of DVP-PLC Device Number
      • D.4.2 Devices Functions
      • D.4.3 Value, Constant [K] / [H]
      • D.4.4 The Function of Auxiliary Relay
      • D.4.5 The Function of Timer
      • D.4.6 The Features and Functions of Counter
      • D.4.7 Register Types
      • D.4.8 Special Auxiliary Relays
      • D.4.9 Special Registers
      • D.4.10 Communication Addresses for Devices (only for PLC2 mode)
      • D.4.11 Function Code (only for PLC2 mode)
    • D.5 Commands
      • D.5.1 Basic Commands
      • D.5.2 Output Commands
      • D.5.3 Timer and Counters
      • D.5.4 Main Control Commands
      • D.5.5 Rising-edge/falling-edge Detection Commands of Contact
      • D.5.6 Rising-edge/falling-edge Output Commands
      • D.5.7 End Command
      • D.5.8 Explanation for the Commands
      • D.5.9 Description of the Application Commands
      • D.5.10 Explanation for the Application Commands
      • D.5.11 Special Application Commands for the AC Motor Drive
    • D.6 Error Code
  • Appendix E CANopen Function
    • E.1 Overview
      • E.1.1 CANopen Protocol
      • E.1.2 RJ-45 Pin Definition
      • E.1.3 Pre-Defined Connection Set
      • E.1.4 CANopen Communication Protocol
        • E.1.4.1 NMT (Network Management Object)
        • E.1.4.2 SDO (Service Data Object)
        • E.1.4.3 PDO (Process Data Object)
        • E.1.4.4 EMCY (Emergency Object)
    • E.2 How to Control by CANopen